Home › Vehicle Exterior › WINDOW / GLASS › REAR POWER WINDOW SWITCH

REAR POWER WINDOW SWITCH > INSPECTION

for Preparation Click here



1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)


    B203473E29
  1. Check the switch function.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      6 (UP) - 1 (GND)
      Auto up or up position
      Below 1 Ω
      7 (DOWN) - 1 (GND)
      Auto down or down position
      Below 1 Ω
      8 (AUTO) - 1 (GND)
      Auto up or auto down position
      Below 1 Ω
      6 (UP) - 1 (GND)
      Free
      10 kΩ or higher
      7 (DOWN) - 1 (GND)
      Free
      10 kΩ or higher
      8 (AUTO) - 1 (GND)
      Free
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (Rear Power Window Regulator Switch Assembly (for LH Door))
      If the result is not as specified, replace the rear power window regulator switch assembly (for LH door).



    B203473E32
  1. Check that the LED illuminates.

    1. Apply auxiliary battery voltage to the rear power window regulator switch assembly and check that the LED illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Auxiliary battery positive (+) → 4 (LED)
      Auxiliary battery negative (-) → 1 (GND)
      LED illuminates

      Text in Illustration 
      *a
      Component without harness connected
      (Rear Power Window Regulator Switch Assembly (for LH door))
      *b
      LED
      If the result is not as specified, replace the rear power window regulator switch assembly (for LH door).



2. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)


    B203473E29
  1. Check the switch function.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      6 (UP) - 1 (GND)
      Auto up or up position
      Below 1 Ω
      7 (DOWN) - 1 (GND)
      Auto down or down position
      Below 1 Ω
      8 (AUTO) - 1 (GND)
      Auto up or auto down position
      Below 1 Ω
      6 (UP) - 1 (GND)
      Free
      10 kΩ or higher
      7 (DOWN) - 1 (GND)
      Free
      10 kΩ or higher
      8 (AUTO) - 1 (GND)
      Free
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (Rear Power Window Regulator Switch Assembly (for RH Door))
      If the result is not as specified, replace the rear power window regulator switch assembly (for RH door).



    B203473E32
  1. Check that the LED illuminates.

    1. Apply auxiliary battery voltage to the rear power window regulator switch assembly and check that the LED illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Auxiliary battery positive (+) → 4 (LED)
      Auxiliary battery negative (-) → 1 (GND)
      LED illuminates

      Text in Illustration 
      *a
      Component without harness connected
      (Rear Power Window Regulator Switch Assembly (for RH Door))
      *b
      LED
      If the result is not as specified, replace the rear power window regulator switch assembly (for RH door).