Home › Engine / Hybrid System › 2AR-FXE INTAKE / EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the No. 2 exhaust manifold heat insulator with the 2 bolts.

    Torque:
    14 N*m{ 138 kgf*cm , 10 ft.*lbf }



2. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
  1. Set a new gasket to the cylinder head sub-assembly.

  1. Temporarily install the exhaust manifold converter sub-assembly with the 5 nuts.

  1. Temporarily install the No. 2 manifold stay and manifold stay with the 2 bolts and 2 nuts.



    A195979E04
  1. Tighten the 5 nuts in the order shown in the illustration.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



3. INSTALL MANIFOLD STAY


    A257339E01
  1. Tighten the bolt and nut in the order shown in the illustration.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



4. INSTALL NO. 2 MANIFOLD STAY


    A257340E01
  1. Tighten the bolt and nut in the order shown in the illustration.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



5. INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR
  1. Install the No. 1 manifold converter insulator with the 3 bolts.

    Torque:
    14 N*m{ 138 kgf*cm , 10 ft.*lbf }



6. INSTALL AIR FUEL RATIO SENSOR


    A254804E01
  1. Using SST, install the air fuel ratio sensor to the exhaust manifold.
    Text in Illustration 
    *a
    Fulcrum Length
    30 mm
    *b
    Fulcrum Length
    300 mm

    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    1. The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.) and a torque wrench with a fulcrum length of 300 mm (11.81 in.) (Click here).
    2. The "with SST" torque value is effective when SST is parallel to the torque wrench.

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).

  1. Connect the air fuel ratio sensor connector.

  1. Install the hose clamp.



7. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the No. 1 exhaust manifold heat insulator with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



8. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A077857E03
  1. Using a vernier caliper, measure the free length of the compression spring.
    Standard
    42.0 mm (1.65 in.)
    Minimum
    40.5 mm (1.60 in.)

    HINT:
    If the length is less than the minimum, replace the compression spring.

  1. Fully insert a new gasket to the exhaust manifold converter sub-assembly.



    A104635E14
  1. Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.
    Text in Illustration 
    *1
    Exhaust Manifold Converter Sub-assembly
    *2
    Wooden Block
    *3
    Gasket

    NOTICE:
    1. Be sure to install the gasket in the correct direction.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. Do not push in the gasket by using the exhaust pipe when connecting it.

  1. Install a new gasket to the front exhaust pipe assembly.

  1. Connect the front exhaust pipe assembly to the exhaust pipe support.



  1. Install the front exhaust pipe assembly with the 2 compression springs, 2 bolts and 2 nuts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


    HINT:
    A258941E01
    After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.
    Text in Illustration 
    *1
    Exhaust Manifold Converter Sub-assembly
    *2
    Front Exhaust Pipe Assembly
    *3
    Gasket
    *a
    Space between flanges: 8.5 mm (0.335 in.)

  1. Connect the heated oxygen sensor connector.



9. INSTALL ENGINE UNDER COVER LH


10. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH


11. INSTALL ENGINE UNDER COVER RH


12. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH


13. INSPECT FOR EXHAUST GAS LEAK