Home › Engine / Hybrid System › 2AR-FXE INTAKE / EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the No. 2 exhaust manifold heat insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 2 bolts.

    Torque:
    14 N*m{ 138 kgf*cm , 10 ft.*lbf }



2. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)
  1. Install a new gasket to the cylinder head sub-assembly.

  1. Temporarily install the exhaust manifold converter sub-assembly (TWC: Front Catalyst) to the cylinder head sub-assembly with the 5 nuts.

  1. Temporarily install the No. 2 manifold stay to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly with the bolt and nut.

  1. Temporarily install the manifold stay to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly with the bolt and nut.



    A195979E07
  1. Tighten the 5 nuts in the order shown in the illustration.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



3. INSTALL MANIFOLD STAY


    A257339E03
  1. Tighten the bolt and nut in the order shown in the illustration.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



4. INSTALL NO. 2 MANIFOLD STAY


    A257340E03
  1. Tighten the bolt and nut in the order shown in the illustration.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



5. INSTALL NO. 2 EGR PIPE (w/ EGR System)
  1. Install 2 new gaskets to the No. 2 EGR pipe.

  1. Install the No. 2 EGR pipe to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and EGR cooler assembly with the 2 bolts and 2 nuts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



6. INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR
  1. Install the No. 1 manifold converter insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 3 bolts.

    Torque:
    14 N*m{ 138 kgf*cm , 10 ft.*lbf }



7. INSTALL AIR FUEL RATIO SENSOR


    A254804E01
  1. Using SST, install the air fuel ratio sensor to the exhaust manifold.
    Text in Illustration 
    *a
    Fulcrum Length
    30 mm
    *b
    Fulcrum Length
    300 mm

    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    1. The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.) and a torque wrench with a fulcrum length of 300 mm (11.81 in.) (Click here).
    2. The "with SST" torque value is effective when SST is parallel to the torque wrench.

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
    1. w/ EGR System: (Click here)
    2. w/o EGR System: (Click here)

  1. Connect the air fuel ratio sensor connector.

  1. Install the hose clamp.



8. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the No. 1 exhaust manifold heat insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



9. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)


    A077857E03
  1. Using a vernier caliper, measure the free length of the compression springs.
    Standard
    42.0 mm (1.65 in.)
    Minimum
    40.5 mm (1.60 in.)
    If the length is less than the minimum, replace the compression spring.

  1. Temporarily install a new gasket to the exhaust manifold converter sub-assembly (TWC: Front Catalyst).



    A104635E18
  1. Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the exhaust manifold converter sub-assembly (TWC: Front Catalyst).
    Text in Illustration 
    *1
    Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
    *2
    Gasket
    *a
    Wooden Block

    NOTICE:
    1. Be sure to install the gasket in the correct direction.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. Do not push in the gasket by using the exhaust pipe when connecting it.

  1. Install a new gasket to the front exhaust pipe assembly (TWC: Rear Catalyst).

  1. Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust pipe support.



  1. Install the front exhaust pipe assembly (TWC: Rear Catalyst) with the 2 compression springs, 2 bolts and 2 nuts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


    HINT:
    A258941E04
    After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) are consistent front-to-rear and left-to-right.
    Text in Illustration 
    *1
    Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
    *2
    Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
    *3
    Gasket
    *a
    Space between Flanges: 8.5 mm (0.335 in.)

  1. Connect the heated oxygen sensor connector.



10. INSTALL ENGINE UNDER COVER LH


11. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH


12. INSTALL ENGINE UNDER COVER RH


13. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH


14. INSPECT FOR EXHAUST GAS LEAK