Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

DTC    B279A    Theft Deterrent System Communication Line High Fixation

for Preparation Click here


DESCRIPTION

When the communication line (IMI - EFIO) between the power management control ECU and certification ECU (smart key ECU assembly) is stuck high, the power management control ECU stores this DTC.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B279A
The communication line (IMI - EFIO) between the power management control ECU and certification ECU (smart key ECU assembly) is stuck high (1 trip detection logic*).
  1. Wire harness or connector (disconnection or break in wire harness is main cause)
  2. Certification ECU (smart key ECU assembly)
  3. Power management control ECU
Turn the power switch on (IG) and wait 6 seconds.
  1. *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started
Hybrid control system cannot be started

Related Data List and Active Test 
DTC Code
Data List and Active Test
B279A
-

WIRING DIAGRAM


B271007E51


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

HINT:
When DTC B279A and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK DTC OUTPUT
  1. Turn the power switch on (IG) and wait 10 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B279A is output
    A
    DTC B279A and other DTCs are output
    B

    HINT:
    If DTCs other than DTC B279A are output, troubleshoot those DTCs first.



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3.CHECK CONNECTION OF CONNECTOR
  1. Turn the power switch off.

  1. Check that the connectors are properly connected to the power management control ECU and certification ECU (smart key ECU assembly).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the I87 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the I4 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I87-14 (EFIO) - I4-29 (IMI)
    Always
    Below 1 Ω
    I87-14 (EFIO) or I4-29 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    Refer to the Service Bulletin.


NEXT


6.REGISTER RECOGNITION CODES
  1. Register the recognition codes in the ECUs.

    HINT:
    Refer to the Service Bulletin.


NEXT


7.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


8.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


9.CHECK DTC OUTPUT
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B279A is not output.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)