Home › Brake › BRAKE (FRONT) › FRONT BRAKE FLEXIBLE HOSE

FRONT BRAKE FLEXIBLE HOSE > INSTALLATION

for Preparation Click here


NOTICE:
  1. Because the left and right hoses are not interchangeable, verify the part number when installing the flexible hoses.
  2. If the hoses are to be reused, connect them after checking the identification marks placed when each hose was disconnected.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. INSTALL FRONT FLEXIBLE HOSE
  1. Install a new clip to the front flexible hose.

    NOTICE:
    Install the clip as far as it will go.

  1. Using a union nut wrench, connect the brake line to the front flexible hose while holding the flexible hose with a wrench.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. Do not bend or damage the brake line.
    2. Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting points.
    3. Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).



    C239561E01
  1. Install the front speed sensor clamp and front flexible hose to the shock absorber bracket with the bolt.
    Text in Illustration 
    *1
    Front Speed Sensor Clamp
    *2
    Front Flexible Hose
    *3
    Claw

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }

    NOTICE:
    1. Do not twist the wire harness for the front speed sensor when installing it.
    2. Securely set the 2 claws of the front speed sensor clamp to the shock absorber bracket.
    3. A bolt tightens the brake flexible hose and front speed sensor together. Make sure that the front flexible hose is positioned over the front speed sensor.



    C238481E01
  1. Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.
    Text in Illustration 
    *a
    Lock Hole

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose lock securely into the lock hole in the front disc brake cylinder.



2. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL



3. BLEED BRAKE LINE


  1. Bleed brake line.



      C239900
    1. Remove the brake master cylinder reservoir filler cap assembly.

    2. Add brake fluid into the reservoir between the MAX and MIN level on the brake fluid reservoir.

      Brake fluid:
      SAE J1703 or FMVSS No. 116 DOT3

    3. Connect the intelligent tester to the DLC3 and turn the power switch on (IG).

    4. Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.

    5. Select "Usual air bleeding" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.

    6. After air bleeding, tighten each bleeder plug.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    7. Clear the DTCs (Click here).

    8. Turn the intelligent tester off and turn the power switch off.

  1. Inspect for brake fluid leaks.

  1. Install the brake master cylinder reservoir filler cap.



4. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
  1. Install the front outer cowl top panel sub-assembly with the 10 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.



5. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)



6. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }