Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for LHD)

BRAKE PEDAL (for LHD) > ADJUSTMENT

for Preparation Click here



1. INSPECT AND ADJUST BRAKE PEDAL HEIGHT


  1. Check the brake pedal height.

    1. Turn back the carpet.

    2. Turn back the dash panel insulator assembly from the slit provided on the dash panel insulator assembly.



    3. C239906E01
    4. Measure the shortest distance between the brake pedal pad surface and dash panel sub-assembly.
      Text in Illustration 
      *1
      Stop Light Switch Assembly
      *2
      Dash Panel Sub-assembly
      *a
      Brake Pedal Height

      Pedal height from dash panel sub-assembly:
      138.5 to 148.5 mm (5.46 to 5.84 in.)

      If pedal height is incorrect, inspect and adjust the push rod length according to the procedure below.



  1. Adjust the push rod length.

    1. Remove the stop light switch assembly (Click here).

    2. Remove the brake booster with master cylinder assembly (Click here).



    3. C242735E01
    4. Loosen the lock nut and adjust the push rod length shown in the illustration by turning the brake master cylinder push rod clevis to achieve the correct length.
      Text in Illustration 
      *1
      Lock Nut
      *2
      Brake Master Cylinder Push Rod Clevis
      *a
      Push Rod Length

      Push rod length:
      115.5 to 116.5 mm (4.55 to 4.58 in.)

    5. Tighten the lock nut.

      Torque:
      26 N*m{ 260 kgf*cm , 19 ft.*lbf }

    6. Install the brake booster with master cylinder assembly (Click here).

      1. If the pedal height is incorrect even when the push rod length is adjusted, check the brake pedal support assembly and dash panel.
      2. If necessary, replace the brake pedal support assembly.

    7. Install the stop light switch assembly (Click here).

  1. After adjusting the pedal height, check the brake pedal free play.



2. INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY


    C245588
  1. Loosen the 2 bolts.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Data List "Stroke Sensor".



    C242699
  1. Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

    Standard voltage (without the brake pedal depressed):
    0.8 to 1.2 V



    C245588
  1. Tighten the 2 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not depress the brake pedal after turning the power switch on (IG).

  1. Turn the intelligent tester off and turn the power switch off.

  1. Disconnect the intelligent tester.



3. INSPECT BRAKE PEDAL FREE PLAY


    C132708E05
  1. Depress the pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.
    Text in Illustration 
    *a
    Brake Pedal Free Play

    Pedal free play:
    1.0 to 6.0 mm (0.0394 to 0.236 in.)

    If the pedal free play is not as specified, check the stop light switch clearance . If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.



4. INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:
Measure the distance at the same point used for the brake pedal height inspection.

  1. Release the parking brake.

  1. With the power switch on (READY), depress the brake pedal and measure the pedal reserve distance.

    Pedal reserve distance from the dash panel sub-assembly at 500 N (51 kgf, 112 lbf):
    More than 92 mm (3.62 in.)

    If the distance is not as specified, troubleshoot the brake system (Click here).



5. PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE
(Click here)