Home › Engine / Hybrid System › 2AR-FXE COOLING › COOLING FAN SYSTEM

COOLING FAN SYSTEM > Cooling Fan Circuit

for Preparation Click here


DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed and vehicle speed, and sends the signals to the cooling fan ECU to regulate the cooling fans. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness.

WIRING DIAGRAM


A264934E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.

  1. Check the operation of the cooling fans while operating them using the tester.

    OK:

    Tester Operation
    Specified Condition
    ON
    Cooling fans operating
    OFF
    Cooling fans stopped


    Result:

    Result
    Proceed to
    OK
    A
    NG (Cooling fans do not operate)
    B
    NG (Cooling fans do not stop)
    C



B
Go to step 2

C
Go to step 15
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT COOLING FAN MOTOR (COOLING FAN MOTOR AND NO. 2 COOLING FAN MOTOR)
  1. Inspect the cooling fan motor and No. 2 cooling fan motor (Click here).

    Result:

    Result
    Proceed to
    OK
    A
    NG (Cooling fan motor)
    B
    NG (No. 2 cooling fan motor)
    C



B
REPLACE COOLING FAN MOTOR (Click here)

C
REPLACE NO.2 COOLING FAN MOTOR (Click here)
A


3.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU POWER SOURCE)


    A254660E03
  1. Disconnect the cooling fan ECU connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A10-3 (+B1) - A10-1 (E1)
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Cooling Fan ECU)



NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
  1. Disconnect the ECM connector.

  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A25-44 (RFC) or A10-2 (SI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A10-1 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - BODY GROUND)
OK


6.INSPECT FAN RELAY
  1. Inspect the FAN relay (Click here).



NG
REPLACE FAN RELAY
OK


7.CHECK HARNESS AND CONNECTOR (FAN RELAY POWER SOURCE)


    A264817E01
  1. Remove the FAN relay from the engine room relay block and junction block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3 (FAN relay) - Body ground
    Power switch off
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block and Junction Block Assembly
    *2
    FAN Relay



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - AUXILIARY BATTERY)
OK


8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN RELAY)
  1. Remove the FAN relay from the engine room relay block and junction block assembly.

  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A10-3 (+B1) - 5 (FAN relay)
    Always
    Below 1 Ω
    A10-3 (+B1) or 5 (FAN relay) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - FAN RELAY)
OK


9.CHECK HARNESS AND CONNECTOR (FAN RELAY - BODY GROUND)
  1. Remove the FAN relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2 (FAN relay) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - BODY GROUND)
OK


10.CHECK HARNESS AND CONNECTOR (FAN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Remove the FAN relay from the engine room relay block and junction block assembly.

  1. Disconnect the instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1(FAN relay) - 3D-36
    Always
    Below 1 Ω
    1(FAN relay) or 3D-36 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
OK


11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY)


    A263496E01
  1. Disconnect the instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (LHD):
    Tester Connection
    Condition
    Specified Condition
    3E-1 - 3D-36
    Auxiliary battery voltage is not applied between terminals 3A-27 and 3B-7
    10 kΩ or higher
    3E-1 - 3D-36
    Auxiliary battery voltage is applied between terminals 3A-27 and 3B-7
    Below 1 Ω

    Standard Resistance (RHD):
    Tester Connection
    Condition
    Specified Condition
    3F-1 - 3D-36
    Auxiliary battery voltage is not applied between terminals 3A-27 and 3B-7
    10 kΩ or higher
    3F-1 - 3D-36
    Auxiliary battery voltage is applied between terminals 3A-27 and 3B-7
    Below 1 Ω

    Text in Illustration 
    *1
    Instrument Panel Junction Block Assembly



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY)
OK


12.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY POWER SOURCE)


    A258037E03
  1. Disconnect the instrument panel junction block assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (LHD):
    Tester Connection
    Condition
    Specified Condition
    3E-1 - Body ground
    Power switch off
    11 to 14 V

    Standard Voltage (RHD):
    Tester Connection
    Condition
    Specified Condition
    3F-1 - Body ground
    Power switch off
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Instrument Panel Junction Block Assembly)
    *b
    LHD
    *c
    RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AUXILIARY BATTERY)
OK


13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
  1. Disconnect the instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3B-7 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
OK


14.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the instrument panel junction block assembly connector.

  1. Disconnect the power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3A-27 - I4-2 (IG1D)
    Always
    Below 1 Ω
    3A-27 or I4-2 (IG1D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
OK

CHECK SMART ENTRY AND START SYSTEM (Click here)  

15.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
  1. Disconnect the ECM connector.

  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A25-44 (RFC) - A10-2 (SI)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)
OK


16.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)


    A255683E03
  1. Disconnect the cooling fan motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z14-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Cooling Fan Motor)



NG
REPLACE COOLING FAN MOTOR (Click here)
OK


17.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - BODY GROUND)


    A255684E03
  1. Disconnect the No. 2 cooling fan motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z15-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (No. 2 Cooling Fan Motor)



NG
REPLACE NO.2 COOLING FAN MOTOR (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)