Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD)

BRAKE BOOSTER (for RHD) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal, Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).



2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


3. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY


    C243048
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C245589
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C243049
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



4. DISABLE BRAKE CONTROL
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C242738
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



5. DRAIN BRAKE FLUID

NOTICE:
If brake fluid leaks onto any painted surface, immediately clean it off.



6. REMOVE COOL AIR INTAKE DUCT SEAL


    B287250
  1. Remove the 9 clips and cool air intake duct seal.



7. REMOVE INLET AIR CLEANER ASSEMBLY


    A259747
  1. Remove the 2 bolts and inlet air cleaner assembly.



8. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A259032
  1. Disconnect the mass air flow meter connector and wire harness clamp from the air cleaner cap sub-assembly.

  1. Disconnect the ventilation hose from the cylinder head cover.

  1. Disconnect the connector.



    A259031
  1. Release the 2 clamps and remove the air cleaner cap sub-assembly.



    A259684E01
  1. Disconnect the 2 fuel vapor feed hoses.
    Text in Illustration 
    *1
    Retainer
    *2
    Fuel Tube Connector
    *3
    Pipe
    *4
    O-ring
    *a
    Pull

    NOTICE:
    1. Remove any dirt or foreign matter on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel vapor feed hose.



    A259033
  1. Loosen the hose clamp and disconnect the air cleaner hose from the throttle with motor body assembly.



9. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


10. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A259768E03
  1. Remove the 2 bolts and air cleaner case sub-assembly.
    Text in Illustration 
    *a
    Projection



11. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY


    C242740
  1. Disengage the clamp of the wire harness.

  1. Remove the 2 bolts and separate the brake master cylinder reservoir assembly from the reservoir bracket.



12. SEPARATE RESERVOIR TUBE


    C242741
  1. Remove the 2 bolts and nut, and separate the reservoir tube from the vehicle body.



13. DISCONNECT NO. 2 RESERVOIR HOSE


    C242742
  1. Move the clip and disconnect the No. 2 reservoir hose from the brake master with master cylinder assembly.



14. DISCONNECT NO. 1 RESERVOIR HOSE


    C242743
  1. Move the clip and disconnect the No. 1 reservoir hose from the brake master with master cylinder assembly.



15. REMOVE PUSH ROD PIN


    C243045
  1. Remove the clip and push rod pin.

  1. Separate the brake master cylinder push rod clevis from the brake pedal support assembly.



16. REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY


    C243025E01
  1. Put matchmarks at the position where the wire harness clamp is installed.
    Text in Illustration 
    *a
    Matchmark
    V100135
    Cut

  1. Cut the wire harness clamp and separate the wire harness from the brake booster with master cylinder assembly.



    C243021
  1. Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.
    Text in Illustration 
    V100135
    Release the lock lever
    V100136
    Disconnect the connector



    C245590E01
  1. Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.

  1. Use tags or make a memo to identify the places to reconnect.
    Text in Illustration 
    *a
    to Front Wheel Cylinder LH (Way)
    *b
    to Rear Wheel Cylinder RH
    *c
    to Brake Booster Pump Assembly
    *d
    to Rear Wheel Cylinder LH
    *e
    to Front Wheel Cylinder RH



    C243050E01
  1. Remove the 4 nuts and brake booster with master cylinder assembly.
    Text in Illustration 
    *1
    Connector Portion
    *2
    Union
    *3
    Brake Master Cylinder Push Rod Clevis
    *4
    Boot
    *5
    Front No. 2 Brake Tube

    NOTICE:
    1. Do not kink or damage the brake lines.
    2. Do not carry the brake booster with master cylinder assembly by the parts shown in bold in the illustration.
    3. Be careful not to allow any brake fluid to enter the connector.



    C243057
  1. Turn the wire harness clamp counterclockwise to remove it from the brake booster with master cylinder assembly.



17. REMOVE BRAKE BOOSTER GASKET