BRAKE BOOSTER (for RHD) > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 3. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY |
![]() |
Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.
![]() |
Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.
![]() |
Remove the 10 bolts and front outer cowl top panel sub-assembly.
| 4. DISABLE BRAKE CONTROL |
Wait at least 2 minutes after turning the power switch off.
![]() |
Disconnect the reservoir level switch connector with the parking brake applied.
Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).
Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
Check that the brake pedal can not be further depressed.
Release the parking brake.
| 5. DRAIN BRAKE FLUID |
| 6. REMOVE COOL AIR INTAKE DUCT SEAL |
![]() |
Remove the 9 clips and cool air intake duct seal.
| 7. REMOVE INLET AIR CLEANER ASSEMBLY |
![]() |
Remove the 2 bolts and inlet air cleaner assembly.
| 8. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the mass air flow meter connector and wire harness clamp from the air cleaner cap sub-assembly.
Disconnect the ventilation hose from the cylinder head cover.
Disconnect the connector.
![]() |
Release the 2 clamps and remove the air cleaner cap sub-assembly.
![]() |
Disconnect the 2 fuel vapor feed hoses.
| *1 | Retainer |
| *2 | Fuel Tube Connector |
| *3 | Pipe |
| *4 | O-ring |
| *a | Pull |
![]() |
Loosen the hose clamp and disconnect the air cleaner hose from the throttle with motor body assembly.
| 9. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| 10. REMOVE AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and air cleaner case sub-assembly.
| *a | Projection |
| 11. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY |
![]() |
Disengage the clamp of the wire harness.
Remove the 2 bolts and separate the brake master cylinder reservoir assembly from the reservoir bracket.
| 12. SEPARATE RESERVOIR TUBE |
![]() |
Remove the 2 bolts and nut, and separate the reservoir tube from the vehicle body.
| 13. DISCONNECT NO. 2 RESERVOIR HOSE |
![]() |
Move the clip and disconnect the No. 2 reservoir hose from the brake master with master cylinder assembly.
| 14. DISCONNECT NO. 1 RESERVOIR HOSE |
![]() |
Move the clip and disconnect the No. 1 reservoir hose from the brake master with master cylinder assembly.
| 15. REMOVE PUSH ROD PIN |
![]() |
Remove the clip and push rod pin.
Separate the brake master cylinder push rod clevis from the brake pedal support assembly.
| 16. REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
![]() |
Put matchmarks at the position where the wire harness clamp is installed.
| *a | Matchmark |
![]() | Cut |
Cut the wire harness clamp and separate the wire harness from the brake booster with master cylinder assembly.
![]() |
Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.
![]() | Release the lock lever |
![]() | Disconnect the connector |
![]() |
Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.
Use tags or make a memo to identify the places to reconnect.
| *a | to Front Wheel Cylinder LH (Way) |
| *b | to Rear Wheel Cylinder RH |
| *c | to Brake Booster Pump Assembly |
| *d | to Rear Wheel Cylinder LH |
| *e | to Front Wheel Cylinder RH |
![]() |
Remove the 4 nuts and brake booster with master cylinder assembly.
| *1 | Connector Portion |
| *2 | Union |
| *3 | Brake Master Cylinder Push Rod Clevis |
| *4 | Boot |
| *5 | Front No. 2 Brake Tube |
![]() |
Turn the wire harness clamp counterclockwise to remove it from the brake booster with master cylinder assembly.
| 17. REMOVE BRAKE BOOSTER GASKET |