Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

LIN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



  2. Disconnect the I12 main body ECU (multiplex network body ECU) and 3B instrument panel junction block assembly connectors.


    B282096E25


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  3. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-30 (BECU) - Body ground
    V - Body ground
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    3B-7 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    I12-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reinstall the main body ECU (multiplex network body ECU) to instrument panel junction block assembly.

  5. Reconnect the I12 main body ECU (multiplex network body ECU) and 3B instrument panel junction block assembly connectors.

  6. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3C-26 (LIN2) - 3B-7 (GND1)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    3B-30 (LIN2) - 3B-7 (GND1)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)


  1. Disconnect the K9*1 or J9*2 power window regulator motor assembly (for driver door) connector.

    1. *1: for LHD
    2. *2: for RHD

    B286202E01


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K9-2 (B) - K9-1 (GND)
    GR - W-B
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    K9-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J9-2 (B) - J9-1 (GND)
    GR - W-B
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    J9-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the K9*1 or J9*2 power window regulator motor assembly (for driver door) connector.

    1. *1: for LHD
    2. *2: for RHD

  4. Check for pulses according to the value(s) in the table below.

    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K9-9 (LIN) - K9-1 (GND)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J9-9 (LIN) - J9-1 (GND)
    L - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the power window regulator motor assembly (for driver door) may be malfunctioning.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)


  1. Disconnect the J9*1 or K9*2 power window regulator motor assembly (for front passenger door) connector.

    1. *1: for LHD
    2. *2: for RHD

    B286202E02


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J9-2 (B) - J9-1 (GND)
    GR - W-B
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    J9-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K9-2 (B) - K9-1 (GND)
    GR - W-B
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    K9-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the J9*1 or K9*2 power window regulator motor assembly (for front passenger door) connector.

    1. *1: for LHD
    2. *2: for RHD

  4. Check for pulses according to the value(s) in the table below.

    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J9-9 (LIN) - J9-1 (GND)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K9-9 (LIN) - K9-1 (GND)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the power window regulator motor assembly (for front passenger door) may be malfunctioning.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)


  1. Disconnect the L2 power window regulator motor assembly (for rear RH door) connector.


    B203471E94

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L2-2 (B) - L2-1 (GND)
    G - W-B
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    L2-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L2 power window regulator motor assembly (for rear RH door) connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L2-9 (LIN) - L2-1 (GND)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the power window regulator motor assembly (for rear RH door) may be malfunctioning.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)


  1. Disconnect the M2 power window regulator motor assembly (for rear LH door) connector.


    B203471E95

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M2-2 (B) - M2-1 (GND)
    G - W-B
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    M2-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the M2 power window regulator motor assembly (for rear LH door) connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M2-9 (LIN) - M2-1 (GND)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the power window regulator motor assembly (for rear LH door) may be malfunctioning.


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


  1. Disconnect the K3*1 or J3*2 multiplex network master switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

    B131578E27


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K3-11 (B) - K3-12 (GND)
    W - BR
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    K3-12 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J3-11 (B) - J3-12 (GND)
    W - BR
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    J3-12 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the K3*1 or J3*2 multiplex network master switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  4. Check for pulses according to the value(s) in the table below.

    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K3-17 (LIN1) - K3-12 (GND)
    P - BR
    LIN communication line
    Power switch on (IG)
    Pulse generation

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J3-17 (LIN1) - J3-12 (GND)
    P - BR
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the multiplex network master switch assembly may be malfunctioning.


CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (w/ Sliding Roof System)


  1. Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


    B270994E02

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S4-8 (B) - S4-12 (E)
    B - W-B
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    S4-12 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S4-11 (MPX1) - S4-12 (E)
    P - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the sliding roof ECU (sliding roof drive gear sub-assembly) may be malfunctioning.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. Disconnect the I87 and I86 certification ECU (smart key ECU assembly) connectors.


    B278932E08

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I87-5 (+B) - I86-1 (E)
    W*1 - W-B
    SB*2 - W-B
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    I86-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the I87 and I86 certification ECU (smart key ECU assembly) connectors.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I87-16 (IG) - I86-1 (E)
    BE - W-B
    IG power supply
    Power switch on (IG)
    11 to 14 V
    I87-16 (IG) - I86-1 (E)
    BE - W-B
    IG power supply
    Power switch off
    Below 1 V
    I87-12 (LIN) - I86-1 (E)
    B - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.

    1. *1: for LHD
    2. *2: for RHD


CHECK POWER MANAGEMENT CONTROL ECU


  1. Disconnect the L5 and L6 power management control ECU connectors.


    C146689E47

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I3-1 (AM22) - Body ground
    SB - Body ground
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    I4-7 (AM21) - Body ground
    L - Body ground
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    I3-6 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the I3 and I4 power management control ECU connectors.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I4-11 (LIN2) - I3-6 (E1)
    Y - BR
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the power management control ECU may be malfunctioning.


CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)


    C211401E12
  1. Disconnect the I24 steering lock ECU (steering lock actuator assembly) connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I24-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    I24-7 (B) - Body ground
    B - Body ground
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    I24-6 (IG2) - Body ground
    LG - Body ground
    IG power supply
    Power switch on (IG)
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I24 steering lock ECU (steering lock actuator assembly) connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I24-5 (LIN) - I24-1 (GND)
    Y*1 - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    V*2 - W-B
    LIN communication line
    Power switch on (IG)
    Pulse generation
    If the result is not as specified, the steering lock ECU (steering lock actuator assembly) may be malfunctioning.

    1. *1: w/o Wireless Door Lock Buzzer Answer Back Function
    2. *2: w/ Wireless Door Lock Buzzer Answer Back Function