Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > PTC Heater Circuit

for Preparation Click here


DESCRIPTION

The air conditioning amplifier assembly sends operation signals to the PTC HTR relays when quick heater assembly (PTC heater) operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC HTR relays turn on, and power is supplied to the quick heater assembly (PTC heater) installed in the air conditioning radiator assembly.

Quick Heater Assembly (PTC Heater) Operation Condition 
Control ECU
Condition
Air Conditioning Amplifier Assembly
Blower motor on
Temperature set to MAX HOT
ECO mode switch (eco switch assembly) off
IDH terminal signal less than 1 V
(Inverter with converter assembly overload not detected)
Coolant temperature 70°C or lower
Ambient temperature 10°C or lower

WIRING DIAGRAM


E230450E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Active Test.

  1. Check the operation by referring to the table below.


Air Conditioner 
Tester Display
Test Part
Control Range
Diagnostic Note
Heater Active Level
Quick heater assembly
Min.: 0, Max.: 2
-

OK:
Quick Heater Active Level changes normally.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


2.INSPECT PTC HTR RELAY (PTC HTR NO. 1, PTC HTR NO. 2)


    E218162E05
  1. Remove the PTC HTR NO. 1 relay and PTC HTR NO. 2 relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Auxiliary battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Auxiliary battery voltage is applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE PTC HTR RELAY
OK


3.CHECK HARNESS AND CONNECTOR (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY - POWER SOURCE)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    PTC1 
    Tester Connection
    Condition
    Specified Condition
    3 - Body ground
    Power switch off
    11 to 14 V
    2 - Body ground
    Power switch on (IG)
    11 to 14 V
    PTC2 
    Tester Connection
    Condition
    Specified Condition
    3 - Body ground
    Power switch off
    11 to 14 V
    2 - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the I77 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    PTC1 
    Tester Connection
    Condition
    Specified Condition
    1 - I77-15 (PTC1)
    Always
    Below 1 Ω
    1 - Body ground
    Always
    10 kΩ or higher
    PTC2 
    Tester Connection
    Condition
    Specified Condition
    1 - I77-16 (PTC2)
    Always
    Below 1 Ω
    1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY - QUICK HEATER ASSEMBLY)
  1. Disconnect the I41 quick heater assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    PTC1 
    Tester Connection
    Condition
    Specified Condition
    5 - I41-1 (B)
    Always
    Below 1 Ω
    5 - Body ground
    Always
    10 kΩ or higher
    PTC2 
    Tester Connection
    Condition
    Specified Condition
    5 - I41-2 (B)
    Always
    Below 1 Ω
    5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT QUICK HEATER ASSEMBLY
  1. Remove the quick heater assembly (Click here).



    E230975E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I41-1 (B)- a1-1 (E)
    Always
    Below 1 Ω
    I41-2 (B)- a1-1 (E)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Quick Heater Assembly)



NG
REPLACE QUICK HEATER ASSEMBLY (Click here)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)