Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0851-775    Park / Neutral Switch Input Circuit Low

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P0705-757 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0851
775
N signal line malfunction
  1. Wire harness or connector
  2. Shift lever position sensor
  3. Power management control ECU

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0705-757 .

INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0851-775 only is output.
    A
    P0705-757 is also output.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART (P0705-757) (Click here)
A


2.CHECK SHIFT LEVER POSITION SENSOR
  1. Turn the power switch on (IG).



    A259789E27
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A39-11 (N) - Body ground
    Power switch on (IG)
    Shift lever in N
    11 to 14 V
    A39-11 (N) - Body ground
    Power switch on (IG)
    Except shift lever in N
    1.2 to 2.8 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)

  1. Turn the power switch off.



NG
Go to step 4
OK


3.CHECK FOR INTERMITTENT PROBLEMS
(Click here)


NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
  1. Disconnect the shift lever position sensor connector.

  1. Turn the power switch on (IG).



    A210242E19
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-8 (+B) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Shift Lever Position Sensor)

    NOTICE:
    Turning the power switch on (IG) with the shift lever position sensor connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Connect the shift lever position sensor connector.



NG
Go to step 6
OK


5.INSPECT SHIFT LEVER POSITION SENSOR
  1. Disconnect the shift lever position sensor connector.



    A210243E39
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E73-8 (+B) - E73-2 (N)
    Shift lever in N
    Below 1 Ω
    E73-8 (+B) - E73-2 (N)
    Except shift lever in N
    4.2 to 5.2 kΩ

    Text in Illustration 
    *a
    Component without harness connected
    (Shift Lever Position Sensor)

  1. Connect the shift lever position sensor connector.



NG
REPLACE SHIFT LEVER POSITION SENSOR (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

6.CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the E73 shift lever position sensor connector.

  1. Disconnect the A38 power management control ECU connector.



    A378806E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E73-8 (+B) - A38-9 (PSFT)
    Power switch off
    Below 1 Ω
    E73-8 (+B) or A38-9 (PSFT) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Shift Lever Position Sensor)
    *b
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Reconnect the A38 power management control ECU connector.

  1. Reconnect the E73 shift lever position sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE POWER SOURCE CIRCUIT