ENGINE UNIT > INSPECTION |
| 1. INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
![]() |
Turn the roller by hand to check that it turns smoothly.
If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.
| 2. INSPECT VALVE LASH ADJUSTER ASSEMBLY |
![]() |
| *1 | Plunger |
| *2 | Check Ball |
| *a | CORRECT |
| *b | INCORRECT |
| *c | Taper Part |
| *d | Low Pressure Chamber |
| *e | High Pressure Chamber |
Place the lash adjuster into a container full of new engine oil.
Insert the tip of SST into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.
Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.
Check the movement of the plunger and bleed the air.
After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.
| 3. INSPECT CAMSHAFT OIL CLEARANCE |
Clean the bearing caps, camshaft housing and camshaft journals.
Place the camshafts on the camshaft housing.
![]() |
Lay a strip of Plastigage across each of the camshaft journals.
| *1 | Plastigage |
Install the camshaft bearing caps .
Install the camshaft housing sub-assembly .
Remove the camshaft bearing caps .
![]() |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
| Intake No. 1 journal | 0.035 to 0.072 mm (0.00137 to 0.00283 in.) |
| Exhaust No. 1 journal | 0.005 to 0.054 mm (0.000197 to 0.00213 in.) |
| Other journal | 0.025 to 0.062 mm (0.000984 to 0.00244 in.) |
| Item | Specified Condition |
| Intake No. 1 journal | 0.085 mm (0.00335 in.) |
| Exhaust No. 1 journal | 0.085 mm (0.00335 in.) |
| Other journal | 0.085 mm (0.00335 in.) |
| *1 | Plastigage |
| *2 | No. 1 Journal |
| *3 | Other Journal |
| 4. INSPECT CAMSHAFT THRUST CLEARANCE |
Clean the bearing caps, camshaft housing and camshaft journals.
Place the camshafts on the camshaft housing.
Install the camshaft bearing caps .
Install the camshaft housing sub-assembly .
![]() |
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| Item | Specified Condition |
| Intake | 0.060 to 0.155 mm (0.00236 to 0.00610 in.) |
| Exhaust | 0.060 to 0.155 mm (0.00236 to 0.00610 in.) |
| Item | Specified Condition |
| Intake | 0.170 mm (0.00669 in.) |
| Exhaust | 0.170 mm (0.00669 in.) |
| 5. INSPECT CAMSHAFT |
![]() |
Inspect the camshaft runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
| Item | Specified Condition |
| Intake | 43.814 to 43.914 mm (1.725 to 1.729 in.) |
| Exhaust | 42.939 to 43.039 mm (1.691 to 1.694 in.) |
| Item | Specified Condition |
| Intake | 43.704 mm (1.721 in.) |
| Exhaust | 42.829 mm (1.686 in.) |
![]() |
Inspect the camshaft journals.
Using a micrometer, measure the journal diameter.
| Item | Specified Condition |
| No. 1 journal | 34.449 to 34.465 mm (1.356 to 1.357 in.) |
| Other journals | 22.959 to 22.975 mm (0.904 to 0.905 in.) |
| 6. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Align and attach the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear.
| *1 | Pin Hole |
| *2 | Knock Pin |
![]() |
Check that there is no clearance between the camshaft timing gear and camshaft flange.
| *1 | Camshaft Timing Gear |
| *2 | Flange |
| *a | INCORRECT |
| *b | CORRECT |
| *c | Clearance |
| *d | No Clearance |
Secure the camshaft in place by hand, and then install the installation bolt of the camshaft timing gear by hand.
Check the lock of the camshaft timing gear.
Make sure that the camshaft timing gear is locked.
![]() |
Release the lock pin.
| *1 | Rubber |
| *2 | Vinyl Tape |
| *3 | Knock Pin |
| *a | Retard Side Path |
| *b | Advance Side Path |
| *c | Open |
| *d | Close |
Clean the camshaft journal with non-residue solvent.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Open a hole at port A shown in the illustration.
![]() |
While applying approximately 200 kPa (2.0 kgf/ cm2, 29 psi) of air pressure to the oil path, forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).
Check for smooth rotation.
Turn the camshaft timing gear within its movable range (26.5 to 28.5°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.
Remove the vinyl tape and rubber pieces from the camshaft.
Remove the bolt and camshaft timing gear.
| 7. INSPECT CHAIN SUB-ASSEMBLY |
![]() |
Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.
| *a | Measurement Area |
Using a vernier caliper, measure the length of 15 pins.
| 8. INSPECT CAMSHAFT TIMING SPROCKET |
![]() |
Place the chain around the sprocket.
Using a vernier caliper, measure the sprocket diameter with the chain.
| 9. INSPECT CRANKSHAFT TIMING SPROCKET |
![]() |
Place the chain around the sprocket.
Using a vernier caliper, measure the sprocket diameter with the chain.
| 10. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate counterclockwise to release the lock. Push the plunger and check that it moves smoothly.
| *1 | Plunger |
| *2 | Stopper Plate |
| 11. INSPECT CHAIN TENSIONER SLIPPER |
![]() |
Measure the wear depth of the chain tensioner slipper.
| *a | Depth |
| 12. INSPECT NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Measure the wear depth of the No. 1 chain vibration damper.
| *a | Depth |
| 13. INSPECT TIMING CHAIN GUIDE |
![]() |
Measure the wear depth of the timing chain guide.
| *a | Depth |
| 14. INSPECT NO. 1 BALANCE SHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the No. 1 balance shaft back and forth.
| 15. INSPECT NO. 2 BALANCE SHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the No. 2 balance shaft back and forth.
| 16. INSPECT BALANCE SHAFT BACKLASH |
![]() |
Secure the No. 2 balance shaft in place, and then using a dial indicator, measure the backlash of the No. 1 and No. 2 balance shafts as shown in the illustration.
| *a | Fix |
| 17. INSPECT CYLINDER HEAD BOLT |
![]() |
Using a vernier caliper, measure the diameter of the threads at the measurement point.
| *a | Measurement Point |
| 18. INSPECT EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the surface that contacts the cylinder head.