Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER

FRONT SUSPENSION MEMBER > INSTALLATION

for Preparation Click here



1. INSTALL HOLE PLUG
  1. Install each hole plug to the front frame assembly.



2. INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH


    C238985E01
  1. Temporarily install a new front suspension member body mounting rear cushion LH while confirming the installation direction.
    Text in Illustration 
    *a
    View from Underneath
    V100135
    Front of the Vehicle

    NOTICE:
    Position the front suspension member body mounting rear cushion LH in the correct direction.



    C169232E03
  1. Install SST as shown in the illustration.
    Text in Illustration 
    *1
    Front Suspension Member Body Mounting Rear Cushion LH

    SST
    09830-10010   (09830-01010, 09830-01020, 09830-01030, 09830-01060)



    C167152E05
  1. Using SST, install the front suspension member body mounting rear cushion LH as shown in the illustration.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    NOTICE:
    Check that there is no clearance between the front suspension member and the front suspension member body mounting rear cushion LH.



3. INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH


    C238987E01
  1. Temporarily install a new front suspension member body mounting rear cushion RH while confirming the installation direction.
    Text in Illustration 
    *a
    View from Underneath
    V100135
    Front of the Vehicle

    NOTICE:
    Position the front suspension member body mounting rear cushion RH in the correct direction.

  1. Install SST using the same procedure as the front suspension member body mounting rear cushion LH.

    SST
    09830-10010   (09830-01010, 09830-01020, 09830-01030, 09830-01060)

  1. Using SST, install the front suspension member body mounting rear cushion RH.

    SST
    09830-10010   (09830-01010, 09830-01020, 09830-01030, 09830-01060)

    HINT:
    Perform the same procedure as the LH side.



4. INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION


    C238988E01
  1. Temporarily install a new front suspension member body mounting front cushion while confirming the installation direction.
    Text in Illustration 
    *a
    View from Underneath
    V100135
    Front of the Vehicle

    NOTICE:
    Position the front suspension member body mounting front cushion in the correct direction.

  1. Install SST using the same procedure as the front suspension member body mounting rear cushion LH.

    SST
    09830-10010   (09830-01010, 09830-01020, 09830-01030, 09830-01060)



    C167148E05
  1. Using SST, install the front suspension member body mounting front cushion as shown in the illustration.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    SST
    09830-10010   (09830-01010, 09830-01020, 09830-01030, 09830-01060)

    NOTICE:
    Check that there is no clearance between the front suspension member and the front suspension member body mounting front cushion.



5. INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER
  1. Install the 2 front suspension member body mounting rear stoppers to the front frame assembly.



6. INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER
  1. Install the 2 front suspension member body mounting front stoppers to the front frame assembly.



7. INSTALL FRONT SUSPENSION MEMBER DYNAMIC DAMPER
  1. Install the front suspension member dynamic damper to the front frame assembly with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



8. INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
  1. Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly.



    C167143E01
  1. Install the front lower No. 1 suspension arm sub-assembly to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

    Torque:
    Bolt 1, 2:
    200 N*m{ 2039 kgf*cm , 148 ft.*lbf }
    Bolt 3:
    135 N*m{ 1377 kgf*cm , 100 ft.*lbf }

    NOTICE:
    While keeping the nut from rotating, tighten the bolt.



9. INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



10. INSTALL STEERING LINK ASSEMBLY
  1. Install the steering link assembly with the 2 bolts and 2 nuts.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

    NOTICE:
    1. Keep the nut from rotating while turning the bolt because the nut has its own stopper.
    2. Make sure to tighten the bolts starting from the pinion shaft side.



11. INSTALL FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY
  1. Install the front stabilizer bar with 2 front stabilizer link assemblies to the front frame assembly.



12. INSTALL FRONT NO. 1 STABILIZER BRACKET LH
  1. Install the front No. 1 stabilizer bracket LH to the front frame assembly with the 2 bolts.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



13. INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:
Perform the same procedure as the LH side.



14. INSTALL ENGINE MOUNTING INSULATOR LH
  1. Temporarily install the engine mounting insulator LH with the 3 nuts.

    HINT:
    Perform this procedure only when replacement of the engine mounting insulator LH is necessary.



15. INSTALL ENGINE MOUNTING INSULATOR RH
  1. Temporarily install the engine mounting insulator RH with the 3 nuts.

    HINT:
    Perform this procedure only when replacement of the engine mounting insulator RH is necessary.



16. INSTALL FRONT ENGINE MOUNTING INSULATOR
  1. Temporarily install the front engine mounting insulator with the 3 nuts.

    HINT:
    Perform this procedure only when replacement of the front engine mounting insulator is necessary.



17. INSTALL FRONT FRAME ASSEMBLY