HYBRID CONTROL SYSTEM > Pattern Select Switch EV Mode Circuit |

| EV Mode Entry Condition | Tester Display | Specified Condition |
| HV battery charge level | State of Charge (All Bat) | Approximately 50% or higher |
| Accelerator pedal position | Accelerator Degree | Below approximately 30% |
| Engine coolant temperature | Engine Coolant Temp | 20°C (68°F) or higher |
| HV battery temperature | Temp of Batt TB1 to TB3 | Between 10 to 40°C (50 to 104°F) |
| Vehicle speed (Varies depending on engine warm-up condition) | Vehicle Spd | Cold: 30 km/h (19 mph) or less Warmed-up: 40 km/h (25 mph) |
| Win | Charge Control Value | Below -5000 kW |
| Wout | Discharge Control Value | 11500 kW or higher |
| Defroster | - | OFF |
| Cruise control | - | OFF |
| 1.ASK ABOUT VEHICLE CONDITION |
Check if a buzzer sounded and a message was displayed on the multi-information display when attempting to enter EV mode.
| Result | Proceed to |
| No buzzer sounded and no message was displayed on multi-information display. | A |
| A buzzer sounded and a message was displayed on multi-information display. | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (CAN BUS CHECK) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: System Select / CAN Bus Check.
| Result | Proceed to |
| All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. | A |
| None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. | B |
Turn the power switch off.
|
| ||||
| A | |
| 3.CHECK DTC OUTPUT (ALL CODES) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: System Select / Utility / All Codes.
Check DTCs.
| Result | Proceed to |
| No DTCs are output. | A |
| DTCs are output. | B |
Turn the power switch off.
|
| ||||
| A | |
| 4.READ VALUE USING INTELLIGENT TESTER (EV REQUEST, EV SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / EV request, EV Switch.
Read the value displayed on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition |
| EV request | EV mode transition availability/ ON or OFF | In EV mode: ON |
| EV Switch | EV drive mode switch (pattern select switch assembly) condition/ ON or OFF | EV drive mode switch (pattern select switch assembly) being pushed and held: ON |
| Result | Proceed to |
| The intelligent tester display changes according to the EV drive mode switch (pattern select switch assembly) operation. | A |
| The intelligent tester display does not change according to the EV drive mode switch (pattern select switch assembly) operation. | B |
Turn the power switch off.
|
| ||||
| A | ||
| ||
| 5.INSPECT EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY) |
Remove the EV drive mode switch (pattern select switch assembly) (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| I48-4 (S) - I48-1 (E) | EV drive mode switch (pattern select switch assembly) being pushed and held | Below 1 Ω |
| EV drive mode switch (pattern select switch assembly) not pushed | 10 kΩ or higher |
| *a | Component without harness connected (EV Drive Mode Switch (Pattern Select Switch Assembly)) |
Install the EV drive mode switch (pattern select switch assembly).
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY) - BODY GROUND) |
Disconnect connector I48 from the EV drive mode switch (pattern select switch assembly).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I48-1 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to EV Drive Mode Switch (Pattern Select Switch Assembly)) |
Connect the EV drive mode switch (pattern select switch assembly) connector.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY)) |
Disconnect connector I4 from the power management control ECU.
Disconnect connector I48 from the EV drive mode switch (pattern select switch assembly).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I4-9 (EVSW) - I48-4 (S) | Always | Below 1 Ω |
| I4-9 (EVSW) or I48-4 (S) - Body ground | Always | 10 kΩ or higher |
| *a | Rear view of wire harness connector (to Power Management Control ECU) |
| *b | Front view of wire harness connector (to EV Drive Mode Switch (Pattern Select Switch Assembly)) |
Connect the EV drive mode switch (pattern select switch assembly) connector.
Connect the power management control ECU connector.
|
| ||||
| OK | ||
| ||