FRONT SEAT ASSEMBLY > REASSEMBLY |
| 1. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY |
Engage the 4 guides to install the separate type front seatback spring assembly to the front seat frame with adjuster assembly.
Install the 4 bolts.
| 2. INSTALL FRONT NO. 2 SEAT WIRE |
Connect the connectors and engage the wire harness clamps to install the front No. 2 seat wire.
| 3. INSTALL FRONT SEAT WIRE |
Connect the connectors and engage the wire harness clamps to install the front seat wire.
| 4. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System) |
Engage the 2 clamps to install the seat heater control sub-assembly.
Connect the connector.
| 5. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Driver Side) |
Engage the 3 claws to install the front seat cushion edge protector LH.
Install the screw.
| 6. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Driver Side) |
Engage the 3 claws to install the front seat cushion edge protector RH.
Install the screw.
| 7. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Front Passenger Side) |
Engage the 3 claws to install the front seat cushion edge protector LH.
Install the screw.
| 8. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side) |
Engage the 3 claws to install the front seat cushion edge protector RH.
Install the screw.
| 9. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
Engage the 2 guides to install the reclining adjuster inside cover LH.
| 10. INSTALL RECLINING ADJUSTER INSIDE COVER RH |
Engage the 2 guides to install the reclining adjuster inside cover RH.
| 11. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side) |
![]() |
Engage the clip to install the front seat lower cushion shield LH.
Engage the hook as shown in the illustration.
Install the screw.
| 12. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side) |
![]() |
Engage the clip to install the front seat lower cushion shield RH.
Engage the hook as shown in the illustration.
Install the screw.
| 13. INSTALL SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 6 new hog rings.
| 14. INSTALL FRONT SEAT AIRBAG ASSEMBLY |
Install the front seat airbag assembly with 2 new nuts.
Engage the 2 clamps.
Engage the claw and 3 clamps to connect the airbag wire harness.
| 15. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD |
Temporarily install the separate type front seatback cover with pad.
Engage the 4 claws to install the 2 front seat headrest supports.
Install the 2 brackets with the nut.
![]() |
Turn back the separate type front seatback cover.
Using hog ring pliers, install 2 new hog rings.
![]() |
Using hog ring pliers, install 3 new hog rings.
![]() |
Using hog ring pliers, install 5 new hog rings.
| 16. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() |
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 16 new hog rings.
![]() |
Using hog ring pliers, install 2 new hog rings.
| 17. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD |
Temporarily install the separate type front seat cushion cover with pad.
Engage each hook.
w/ Seat Heater System:
Engage the 2 clamps to install the seat heater wire harness.
Connect the connector.
Engage the clamp.
Connect the connector.
Engage the fastener to secure the front seat airbag assembly wire harness.
| 18. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) |
![]() |
Install the front seat inner belt assembly with the nut.
| *1 | Protruding Part |
Engage the clamp.
Engage each clamp under the front seat assembly.
| 19. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side) |
![]() |
Install the front seat inner belt assembly with the nut.
| *1 | Protruding Part |
| 20. INSTALL FRONT SEAT INNER CUSHION SHIELD (for Driver Side) |
Engage the 5 claws and 6 guides to install the front seat inner cushion shield.
| 21. INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side) |
Engage the 5 claws and 7 guides to install the front seat inner cushion shield.
| 22. INSTALL FRONT LUMBAR POWER SEAT SWITCH (for Driver Side) |
Engage the 4 claws to install the front lumbar power seat switch to the front seat cushion shield.
| 23. INSTALL FRONT POWER SEAT SWITCH |
Install the front power seat switch to the front seat cushion shield with the 3 screws.
| 24. INSTALL FRONT SEAT CUSHION SHIELD (for Driver Side) |
Connect the front lumbar power seat switch connector.
Connect the front power seat switch connector.
Engage the 2 wire harness clamps.
Install the wire harness to the wire harness cover.
Engage the 2 claws to close the wire harness cover.
Engage the 4 claws, 7 guides and clip to install the front seat cushion shield.
| 25. INSTALL FRONT SEAT CUSHION SHIELD (for Front Passenger Side) |
Connect the front power seat switch connector.
Engage the 2 wire harness clamps.
Install the wire harness to the wire harness cover.
Engage the 3 claws to close the wire harness cover.
Engage the 4 claws, 8 guides and clip to install the front seat cushion shield.
| 26. INSTALL FRONT NO. 1 SEAT INNER CUSHION SHIELD |
![]() |
Install the clip.
![]() |
Engage the 3 claws and 3 guides to install the front No. 1 seat inner cushion shield as shown in the illustration.
![]() |
Engage the 2 claws to install the front No. 1 seat inner cushion shield to the clip as shown in the illustration.
Install the screw.
| 27. CONNECT SEPARATE TYPE FRONT SEATBACK COVER |
Connect the rubber band of the separate type front seatback cover.
| 28. INSTALL RECLINING POWER SEAT SWITCH KNOB |
Engage the 4 claws to install the reclining power seat switch knob.
| 29. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
Engage the 4 claws to install the slide and vertical power seat switch knob.
| 30. INSTALL SEAT ADJUSTER COVER CAP |
Install the 2 seat adjuster cover caps.