LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for RHD) > INSTALLATION |
| 1. INSTALL LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY |
Engage the 10 clamps and install the luggage door lock control cable sub-assembly.
Engage the 2 clamps and connect the luggage door lock control cable sub-assembly.
Connect the luggage door lock control cable sub-assembly.
![]() |
Engage the guide as shown in the illustration.
![]() |
Install the luggage door lock control cable sub-assembly to the fuel lid lock control cable sub-assembly with the 2 pieces of tape as shown in the illustration.
| *1 | Tape |
| *2 | Fuel Lid Lock Control Cable Sub-assembly |
| *3 | Luggage Door Lock Control Cable Sub-assembly |
| Area | Measurement |
| a | 295 to 305 mm (11.6 to 12.0 in.) |
| b | 935 to 955 mm (3.06 to 3.13 ft.) |
Return the floor carpet to the original position.
Engage the 2 clamps and install the 2 scuff plate clips.
Engage the 3 clamps and connect the wire harness.
| 2. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
![]() |
Connect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly to the fuel lid lock open lever sub-assembly.
| *1 | Luggage Door Lock Control Cable Sub-assembly |
| *2 | Fuel Lid Lock Control Cable Sub-assembly |
![]() |
Engage the guide and install the fuel lid lock open lever sub-assembly as shown in the illustration.
Install the screw.
| 3. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH |
Install the 3 clips.
Engage the fastener and install the luggage compartment inner trim cover RH.
| 4. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
![]() |
Engage the pin to install the No. 1 luggage compartment trim hook.
| *1 | Pin |
| 5. INSTALL LUGGAGE COMPARTMENT FRONT TRIM COVER |
Engage the 2 claws.
Engage the 8 fasteners and install the luggage compartment front trim cover.
| 6. INSTALL REAR FLOOR FINISH PLATE |
![]() |
Engage the 4 clips and install the rear floor finish plate.
Install the 5 clips.
| 7. INSTALL BAGGAGE HOLDER NET |
Install the baggage holder net.
| 8. INSTALL LUGGAGE COMPARTMENT FLOOR MAT |
Install the luggage compartment floor mat.
| 9. INSTALL LUGGAGE COMPARTMENT DOOR COVER |
![]() |
Install the luggage compartment door cover with the 13 clips.
| 10. INSTALL REAR SIDE SEATBACK ASSEMBLY RH |
Place the rear side seatback assembly RH in the cabin.
Engage the hook to install the rear side seatback assembly RH with the bolt.
Connect the rear seat outer belt to the rear seat shoulder belt guide RH.
| 11. INSTALL REAR SEAT CUSHION LOCK HOOK |
![]() |
Engage the claw to install a new rear seat cushion lock hook.
| 12. INSTALL REAR SEAT CUSHION ASSEMBLY |
Place the rear seat cushion assembly in the cabin.
![]() |
Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.
Confirm that the rear seat cushion assembly is firmly installed.
| 13. INSTALL CENTER PILLAR LOWER GARNISH RH |
| 14. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH |
| 15. INSTALL LAP BELT OUTER ANCHOR COVER |
| 16. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
| *1 | Alignment Mark (Blue) |
| 17. INSTALL REAR DOOR SCUFF PLATE RH |
| 18. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
| *1 | Alignment Mark (White) |
| 19. INSTALL FRONT DOOR SCUFF PLATE RH |
| 20. INSTALL FRONT SEAT ASSEMBLY RH |