Home › Vehicle Exterior › DOOR / HATCH › LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for LHD)

LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for LHD) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE FRONT SEAT ASSEMBLY LH
(Click here)


3. REMOVE FRONT DOOR SCUFF PLATE LH


    B395175E01
  1. Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.

  1. Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.

  1. Disengage the 6 claws (C) to remove the front door scuff plate LH.



4. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Disconnect the front door opening trim weatherstrip.



5. REMOVE REAR DOOR SCUFF PLATE LH


    B395176E01
  1. Disengage the claw (A) in the direction indicated by the arrow (1) shown in the illustration.

  1. Disengage the claw (B) in the direction indicated by the arrow (2) shown in the illustration.

  1. Disengage the 4 claws (C) to remove the rear door scuff plate LH.

    HINT:
    Disengage the claws from the front side of the rear door scuff plate LH.



6. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the rear door opening trim weatherstrip LH.



7. REMOVE LAP BELT OUTER ANCHOR COVER


    B271081
  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



8. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B271082
  1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.



9. REMOVE CENTER PILLAR LOWER GARNISH LH


    B278989
  1. Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.



10. REMOVE REAR SEAT CUSHION ASSEMBLY


    B298856E01
  1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



11. REMOVE REAR SEAT CUSHION LOCK HOOK


    B279203
  1. Disengage the claw and remove the rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure for the LH side and RH side.



12. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
  1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide LH.



    B285000
  1. Remove the bolt.

  1. Disengage the hook and remove the rear side seatback assembly LH.

    NOTICE:
    Be careful not to damage the vehicle body.



13. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    B281699
  1. Remove the 13 clips and luggage compartment door cover.



14. REMOVE LUGGAGE COMPARTMENT FLOOR MAT
  1. Remove the luggage compartment floor mat.



15. REMOVE BAGGAGE HOLDER NET
  1. Remove the baggage holder net.



16. REMOVE REAR FLOOR FINISH PLATE


    B287038
  1. Remove the 5 clips.



    B287039
  1. Disengage the 4 clips and remove the rear floor finish plate.



17. REMOVE LUGGAGE COMPARTMENT FRONT TRIM COVER


    B287041
  1. Disengage the 8 fasteners.

  1. Disengage the 2 claws and remove the luggage compartment front trim cover.



18. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    B288530E01
  1. Push the pin and remove the No. 1 luggage compartment trim hook.
    Text in Illustration 
    *1
    Pin



19. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    B287042
  1. Remove the 3 clips.

  1. Disengage the fastener and remove the luggage compartment inner trim cover LH.



20. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    B280595
  1. Remove the screw.



    E227150
  1. Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.



    B280598
  1. Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.



21. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY


    B280599
  1. Disengage the 2 clamps.



    B280639
  1. Disengage the clamp and disconnect the wire harness.



    B280600
  1. Disengage the 2 clamps and remove the 2 scuff plate clips.

  1. Turn back the floor carpet so that the luggage door lock control cable sub-assembly and fuel lid lock control cable sub-assembly can be removed.



    B283878
  1. Disengage the guide as shown in the illustration.



    B283880
  1. Disconnect the luggage door lock control cable sub-assembly.



    B293421
  1. Disengage the clamp and disconnect the luggage door lock control cable sub-assembly.



    B287079E01
  1. Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.
    Text in Illustration 
    *1
    Cutout
    *2
    Guide <A>



    B288519E01
  1. Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.
    Text in Illustration 
    *1
    Cutout
    *2
    Guide <B>



    B287067E01
  1. Pull out the fuel filler opening lid lock retainer with both guides <B> and <C> aligned with the cutouts.
    Text in Illustration 
    *1
    Cutout
    *2
    Guide <C>
    *3
    Guide <B>



    B287069
  1. Disengage the 2 claws and remove the fuel filler opening lid lock retainer.



  1. Disengage the 10 clamps and remove the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.


    B280605E01


    Text in Illustration 
    *1
    Fuel Lid Lock Control Cable Sub-assembly
    *2
    Luggage Door Lock Control Cable Sub-assembly



  1. Using a knife, cut off the clamp as shown in the illustration.


    B280644E01


    Text in Illustration 
    *1
    Tape
    -
    -
    *a
    Cut
    -
    -

    NOTICE:
    Be careful not to damage the vehicle fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

  1. Remove the clamp.

  1. Remove the 3 pieces of tape and luggage door lock control cable sub-assembly.