Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY (for RHD)

FUEL LID LOCK CONTROL CABLE ASSEMBLY (for RHD) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE FRONT SEAT ASSEMBLY RH
(Click here)


3. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side .



4. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side .



5. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side .



6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side .



7. REMOVE LAP BELT OUTER ANCHOR COVER

HINT:
Use the same procedure as for the LH side .



8. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side .



9. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:
Use the same procedure as for the LH side .



10. REMOVE REAR DOOR SCUFF PLATE LH


    B395176E01
  1. Disengage the claw (A) in the direction indicated by the arrow (1) shown in the illustration.

  1. Disengage the claw (B) in the direction indicated by the arrow (2) shown in the illustration.

  1. Disengage the 4 claws (C) to remove the rear door scuff plate LH.

    HINT:
    Disengage the claws from the front side of the rear door scuff plate LH.



11. REMOVE REAR SEAT CUSHION ASSEMBLY


    B298856E01
  1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



12. REMOVE REAR SEAT CUSHION LOCK HOOK


    B279203
  1. Disengage the claw and remove the rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure for the LH side and RH side.



13. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
  1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide LH.



    B285000
  1. Remove the bolt.

  1. Disengage the hook and remove the rear side seatback assembly LH.

    NOTICE:
    Be careful not to damage the vehicle body.



14. REMOVE LUGGAGE COMPARTMENT FLOOR MAT
  1. Remove the luggage compartment floor mat.



15. REMOVE BAGGAGE HOLDER NET
  1. Remove the baggage holder net.



16. REMOVE REAR FLOOR FINISH PLATE


    B287038
  1. Remove the 5 clips.



    B287039
  1. Disengage the 4 clips and remove the rear floor finish plate.



17. REMOVE LUGGAGE COMPARTMENT FRONT TRIM COVER


    B287041
  1. Disengage the 8 fasteners.

  1. Disengage the 2 claws and remove the luggage compartment front trim cover.



18. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    B288530E01
  1. Push the pin and remove the No. 1 luggage compartment trim hook.
    Text in Illustration 
    *1
    Pin



19. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    B287042
  1. Remove the 3 clips.

  1. Disengage the fastener and remove the luggage compartment inner trim cover LH.



20. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    B281743
  1. Remove the screw.



    B281744
  1. Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.



    B281745
  1. Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.



21. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY


    B281746
  1. Disengage the 2 clamps.



    B281747
  1. Disengage the clamp and disconnect the wire harness.



    B281748
  1. Disengage the 2 clamps and remove the 2 scuff plate clips.

  1. Turn back the floor carpet so that the fuel lid lock control cable sub-assembly can be removed.



    B281715E01
  1. Remove the 2 pieces of tape that connect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.
    Text in Illustration 
    *1
    Tape
    *2
    Fuel Lid Lock Control Cable Sub-assembly
    *3
    Luggage Door Lock Control Cable Sub-assembly



    B281719
  1. Remove the No. 2 noise control plate.



    B287079E01
  1. Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.
    Text in Illustration 
    *1
    Cutout
    *2
    Guide <A>



    B288519E01
  1. Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.
    Text in Illustration 
    *1
    Cutout
    *2
    Guide <B>



    B287067E01
  1. Pull out the fuel filler opening lid lock retainer with both guides <B> and <C> aligned with the cutouts.
    Text in Illustration 
    *1
    Cutout
    *2
    Guide <C>
    *3
    Guide <B>



    B287069
  1. Disengage the 2 claws and remove the fuel filler opening lid lock retainer.



  1. Disengage the 7 clamps and remove the fuel lid lock control cable sub-assembly.


    B281720E01


    Text in Illustration 
    *1
    Fuel Lid Lock Control Cable Sub-assembly
    *2
    Luggage Door Lock Control Cable Sub-assembly