Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT BUMPER SIDE RETAINER LH


    B281875
  1. Engage the 2 claws and install the front bumper side retainer LH.

  1. Install the bolt and screw.

    Torque:
    Bolt:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



2. INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:
Use the same procedure as for the LH side.



3. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    B287259
  1. Install the front bumper reinforcement sub-assembly with the 6 bolts.

    Torque:
    61 N*m{ 622 kgf*cm , 45 ft.*lbf }

  1. Engage the 5 clamps.



4. INSTALL FRONT BUMPER ENERGY ABSORBER


    B287261
  1. Engage the 2 guides to install the front bumper energy absorber.



5. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET


    B287265
  1. Engage the 2 claws.

  1. Install the front bumper extension mounting bracket with the 2 screws.



6. INSTALL NO. 1 LOWER RADIATOR GRILLE


    B287268
  1. Engage the 2 guides and 16 claws to install the No. 1 lower radiator grille.



7. INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY


    B287267
  1. Engage the 2 guides and 4 claws.

  1. Install the radiator grille emblem assembly with the 2 screws.



8. INSTALL RADIATOR GRILLE SUB-ASSEMBLY


    B287269
  1. Engage the 10 claws to install the radiator grille sub-assembly.



9. INSTALL FRONT BUMPER HOLE COVER LH


    B287264
  1. Engage the 6 claws to install the front bumper hole cover LH.



10. INSTALL FRONT BUMPER HOLE COVER RH

HINT:
Use the same procedure as for the LH side.



11. INSTALL FOG LIGHT ASSEMBLY LH
  1. Engage the 2 guides to temporarily install the fog light assembly.

  1. Install the fog light assembly with the screw.

    Torque:
    1.6 N*m{ 16 kgf*cm , 14 in.*lbf }

  1. Connect the connector.



12. INSTALL FOG LIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



13. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)


    E232468E01
  1. Engage the 2 claws to install the No. 1 ultrasonic sensor retainer to the front bumper assembly.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    *a
    Keyhole
    *b
    Snap

    NOTICE:
    1. Do not damage the front bumper with the protrusion when installing the retainer.
    2. Securely install the No. 1 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the front bumper.

    HINT:
    1. When installing the retainer, align the keyhole and snap as shown in the illustration.



14. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)


    E228019E01
  1. Engage the 2 claws to install the No. 1 ultrasonic sensor to the No. 1 ultrasonic sensor retainer.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

    NOTICE:
    Push the No. 1 ultrasonic sensor retainer from the outside of the bumper when there is a gap between the retainer and the bumper surface. In this case, do not push on the ultrasonic sensor.



    E228021E01
  1. Connect the connector.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side



15. INSTALL NO. 4 ENGINE ROOM WIRE (w/o TOYOTA Parking Assist-sensor System)


    B287260
  1. Engage the clamp.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Connect the connector to install the No. 4 engine room wire.

    HINT:
    Use the same procedure for the RH side and LH side.



16. INSTALL NO. 4 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)


    B292913
  1. Engage the clamp.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Connect the 2 connectors to install the No. 4 engine room wire.

    HINT:
    Use the same procedure for the RH side and LH side.



17. INSTALL HEADLIGHT CLEANER HOSE


    B292914
  1. Engage the 5 clamps to install the headlight cleaner hose.



18. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH


  1. Engage the guide to the front bumper assembly, then push the tab (A) and engage the claw as shown in the illustration.


    E234318E01

  1. Install the bolt.

    Torque:
    1.1 N*m{ 11 kgf*cm , 10 in.*lbf }

  1. Connect the headlight cleaner hose and engage the clip.

    HINT:
    Use the same procedure for the RH side and LH side.



19. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



20. INSTALL HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH


    E227515
  1. Engage the 2 claws to install the headlight washer nozzle sub-assembly.

    HINT:
    Use the same procedure for the RH side and LH side.



21. INSTALL HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



22. INSTALL LOWER FRONT BUMPER COVER


    B287262E01
  1. Engage the hook.
    Text in Illustration 
    *1
    Hook

  1. Engage the 2 claws to install the lower front bumper cover.



23. INSTALL FRONT FENDER LINER RETAINER


    B287263
  1. Engage the claw and install the front fender liner retainer.

    HINT:
    Use the same procedure for the RH side and LH side.