Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B14B9    Open in Ion Generator Circuit

for Preparation Click here


DESCRIPTION

The ion generator sub-assembly is controlled by the air conditioning amplifier assembly and operates in accordance with the blower with fan motor assembly. The air conditioning amplifier assembly sends a drive signal to the ion generator sub-assembly. When the ion generator receives the drive signal and starts to operate, it outputs an operation condition signal to the air conditioning amplifier assembly.

DTC No.
DTC Detection Condition
Trouble Area
B14B9
Open in ion generator sub-assembly circuit
  1. Ion generator sub-assembly
  2. Harness or connector between ion generator sub-assembly and IG circuit
  3. Harness or connector between ion generator sub-assembly and body ground
  4. Harness or connector between ion generator sub-assembly and air conditioning amplifier assembly
  5. Air conditioning amplifier assembly

WIRING DIAGRAM


E228211E20


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connector the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Active Test.

  1. Check the operation by referring to the table below.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Ion Generator
    Ion generator sub-assembly
    OFF, ON
    -

    OK:
    Ion generator sub-assembly operates normally.


    Result:

    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A


2.CHECK HARNESS AND CONNECTOR (ION GENERATOR SUB-ASSEMBLY - BODY GROUND)
  1. Disconnect the I182 ion generator sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I182-4 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (ION GENERATOR SUB-ASSEMBLY - IG CIRCUIT)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I182-1 (IG) - Body ground
    Power switch off
    Below 1 V
    I182-1 (IG) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (ION GENERATOR SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the I77 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I77-26 (NAIN) - I182-3 (IG+)
    Always
    Below 1 Ω
    I77-39 (NANO) - I182-2 (PCL)
    Always
    Below 1 Ω
    I77-26 (NAIN) - Body ground
    Always
    10 kΩ or higher
    I77-39 (NANO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE ION GENERATOR SUB-ASSEMBLY
  1. Replace the ion generator sub-assembly (Click here).

    HINT:
    Since the ion generator sub-assembly cannot be inspected while it is removed from the vehicle, replace the ion generator sub-assembly with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B14B9 is not output
    A
    DTC B14B9 is output
    B



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A

END (ION GENERATOR SUB-ASSEMBLY WAS DEFECTIVE)