Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B14A3    Front Passenger Side Solar Sensor Short Circuit

for Preparation Click here


DESCRIPTION

E107008E01
The solar sensor (automatic light control sensor) is installed on the upper side of the instrument panel. It detects sunlight and creates a signal that is used for air conditioning control in AUTO mode. The output voltage from the solar sensor (automatic light control sensor) varies in accordance with the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The air conditioning amplifier assembly detects changes in the output voltage from the solar sensor (automatic light control sensor).

DTC No.
DTC Detection Condition
Trouble Area
B14A3
Short in passenger side solar sensor (automatic light control sensor) circuit
  1. Solar sensor (automatic light control sensor)
  2. Harness or connector between solar sensor (automatic light control sensor) and air conditioning amplifier assembly
  3. Harness or connector between solar sensor (automatic light control sensor) and main body ECU (multiplex network body ECU)
  4. Main body ECU (multiplex network body ECU)
  5. Air conditioning amplifier assembly

WIRING DIAGRAM


E229255E02


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Solar Sensor (P Side)
    Front passenger side solar sensor (automatic light control sensor) /
    Min.: 0
    Max.: 255
    Front passenger side solar sensor (automatic light control sensor) value increases as brightness increases
    -

    OK:
    The display is as specified in the Normal Condition column.


    Result:

    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    E221132E11
  1. Disconnect the I61 solar sensor (automatic light control sensor) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I61-6 (CLTB) - I61-3 (CLTE)
    Power switch off
    Below 1 V
    I61-6 (CLTB) - I61-3 (CLTE)
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Solar Sensor (Automatic Light Control Sensor))



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the I77 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I77-32 (TSP) - I61-1 (TSL)*1
    Always
    Below 1 Ω
    I77-32 (TSP) - I61-2 (TSR)*2
    Always
    Below 1 Ω
    I77-32 (TSP) - Body ground
    Always
    10 kΩ or higher

    1. *1: for RHD
    2. *2: for LHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR)


    E221134E15
  1. Remove the solar sensor (automatic light control sensor) (Click here).

  1. Reconnect the I61 solar sensor (automatic light control sensor) connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I61-1 (TSL) - I61-3 (CLTE)*1
    Sensor is subjected to electric light
    0.8 to 4.3 V
    I61-1 (TSL) - I61-3 (CLTE)*1
    Sensor is covered with a cloth
    Below 0.8 V
    I61-2 (TSR) - I61-3 (CLTE)*2
    Sensor is subjected to electric light
    0.8 to 4.3 V
    I61-2 (TSR) - I61-3 (CLTE)*2
    Sensor is covered with a cloth
    Below 0.8 V

    1. *1: for RHD
    2. *2: for LHD

    NOTICE:
    1. The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 1 and the positive (+) lead to terminal 6 of the solar sensor (automatic light control sensor).
    2. Do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    HINT:
    1. Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor (automatic light control sensor).
    2. As the inspection light is moved away from the sensor, the voltage decreases.

    Text in Illustration 
    *A
    for RHD
    *B
    for LHD
    *a
    Component with harness connected
    (Solar Sensor (Automatic Light Control Sensor))



NG
REPLACE (SOLAR SENSOR) AUTOMATIC LIGHT CONTROL SENSOR (Click here)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR))
  1. Disconnect the I13 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I13-20 (CLTB) - I61-6 (CLTB)
    Always
    Below 1 Ω
    I13-18 (CLTE) - I61-3 (CLTE)
    Always
    Below 1 Ω
    I13-20 (CLTB) - Body ground
    Always
    10 kΩ or higher
    I13-18 (CLTE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)