Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > INSPECTION

for Preparation Click here



1. INSPECT CYLINDER HEAD SUB-ASSEMBLY


    A194968E05
  1. Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head contacts the cylinder block and manifold.

    Maximum Warpage:
    Item
    Specified Condition
    Cylinder head lower side
    0.05 mm (0.00197 in.)
    Intake manifold side
    0.10 mm (0.00394 in.)
    Exhaust manifold side
    0.10 mm (0.00394 in.)

    Text in Illustration 
    *a
    Cylinder Head Lower Side
    *b
    Intake Manifold Side
    *c
    Exhaust Manifold Side
    If the warpage is more than the maximum, replace the cylinder head.



    A194969
  1. Using a dye penetrant, check the intake ports, exhaust ports and cylinder head surface for cracks.
    If cracked, replace the cylinder head.



2. INSPECT COMPRESSION SPRING


HINT:
Type A and Type B can be distinguished by the shape of the compression spring.



A361727E01


Text in Illustration 
*A
Type A
(Compression Spring Shape: Straight)
*B
Type B
(Compression Spring Shape: Tapered)
*1
No. 1 Valve Rocker Arm Sub-assembly
*2
Valve Spring Retainer
*3
Compression Spring
*4
Valve Lash Adjuster Assembly


  1. Type A:



      A194990
    1. Using a vernier caliper, measure the free length of the compression spring.

      Standard Free Length:
      Wire Diameter
      Specified Condition
      3.3 mm (0.130 in.)
      49.0 to 51.0 mm (1.93 to 2.01 in.)
      3.4 mm (0.134 in.)
      47.2 to 49.2 mm (1.86 to 1.94 in.)

      If the free length is not as specified, replace the compression spring.



    2. A194991E05
    3. Using a steel square, measure the deviation of the compression spring.

      Maximum deviation:
      1.0 mm (0.0394 in.)

      Maximum angle:
      2°

      Text in Illustration 
      *a
      Deviation
      If the deviation is more than the maximum, replace the compression spring.



  1. Type B:



      A333833
    1. Using a vernier caliper, measure the free length of the compression spring.

      Standard free length:
      47.38 mm (1.87 in.)

      If the free length is not as specified, replace the compression spring.



    2. A335450E03
    3. Using a steel square, measure the deviation of the compression spring at the position shown in the illustration.
      Text in Illustration 
      *a
      Deviation
      *b
      30 mm (1.18 in.)

      Maximum deviation:
      1.0 mm (0.0394 in.)

      If the deviation is more than the maximum, replace the compression spring.



3. INSPECT INTAKE VALVE


    A194992
  1. Using a micrometer, measure the diameter of the valve stem.

    Standard valve stem diameter:
    5.470 to 5.485 mm (0.21535 to 0.21594 in.)



    A194993E05
  1. Using a vernier caliper, measure the valve head margin thickness.

    Standard margin thickness:
    1.0 mm (0.0394 in.)

    Minimum margin thickness:
    0.50 mm (0.0197 in.)

    Text in Illustration 
    *a
    Margin Thickness
    If the margin thickness is less than the minimum, replace the intake valve.



    A194994E04
  1. Using a vernier caliper, measure the overall length of the intake valve.

    Standard overall length:
    103.92 mm (4.09 in.)

    Minimum overall length:
    103.42 mm (4.07 in.)

    Text in Illustration 
    *a
    Overall Length
    If the overall length is less than the minimum, replace the intake valve.



4. INSPECT EXHAUST VALVE


    A194995
  1. Using a micrometer, measure the diameter of the valve stem.

    Standard valve stem diameter:
    5.465 mm to 5.480 mm (0.21516 to 0.21575 in.)



    A194996E05
  1. Using a vernier caliper, measure the valve head margin thickness.

    Standard margin thickness:
    1.0 mm (0.0394 in.)

    Minimum margin thickness:
    0.50 mm (0.0197 in.)

    Text in Illustration 
    *a
    Margin Thickness
    If the margin thickness is less than the minimum, replace the exhaust valve.



    A194997E04
  1. Using a vernier caliper, measure the overall length of the exhaust valve.

    Standard overall length:
    112.91 mm (4.44 in.)

    Minimum overall length:
    112.41 mm (4.43 in.)

    Text in Illustration 
    *a
    Overall Length
    If the overall length is less than the minimum, replace the exhaust valve.



5. INSPECT VALVE GUIDE BUSH OIL CLEARANCE


    A194967
  1. Using a caliper gauge, measure the inside diameter of the guide bush.

    Standard bush inside diameter:
    5.510 to 5.530 mm (0.2169 to 0.2177 in.)

  1. Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

    Standard Oil Clearance:
    Item
    Specified Condition
    Intake
    0.025 to 0.060 mm (0.000984 to 0.00236 in.)
    Exhaust
    0.030 to 0.065 mm (0.00118 to 0.00256 in.)

    Maximum Oil Clearance:
    Item
    Specified Condition
    Intake
    0.08 mm (0.00315 in.)
    Exhaust
    0.10 mm (0.00394 in.)

    If the oil clearance is more than the maximum, replace the valve and guide bush.



6. INSPECT INTAKE VALVE SEAT
  1. Apply a light coat of Prussian blue to the valve face.



    A194998E05
  1. Lightly press the valve face against the valve seat.
    Text in Illustration 
    *a
    Width

    HINT:
    Do not rotate the valve while pressing the valve.

  1. Check the valve face and valve seat.

    1. Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).
      If not, correct the valve seat.

    2. Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
      If not, correct the valve seat.



7. INSPECT EXHAUST VALVE SEAT
  1. Apply a light coat of Prussian blue to the valve face.



    A194999E05
  1. Lightly press the valve face against the valve seat.
    Text in Illustration 
    *a
    Width

    HINT:
    Do not rotate the valve while pressing the valve.

  1. Check the valve face and valve seat.

    1. Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).
      If not, correct the valve seat.

    2. Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
      If not, correct the valve seat.



8. INSPECT CAMSHAFT OIL CLEARANCE

NOTICE:
Do not turn the camshafts.

  1. Clean the bearing caps, camshaft housing and camshaft journals.

  1. Place the camshafts on the camshaft housing.



    A259165E01
  1. Lay a strip of Plastigage across each of the camshaft journals.
    Text in Illustration 
    *1
    Plastigage

  1. Install the camshaft bearing caps .

  1. Install the camshaft housing sub-assembly .

  1. Remove the camshaft bearing caps .



    A259166E01
  1. Measure the Plastigage at its widest point.

    Standard Oil Clearance:
    Item
    Specified Condition
    Intake No. 1 journal
    0.035 to 0.072 mm (0.00137 to 0.00283 in.)
    Exhaust No. 1 journal
    0.005 to 0.054 mm (0.000197 to 0.00213 in.)
    Other journal
    0.025 to 0.062 mm (0.000984 to 0.00244 in.)

    Maximum Oil Clearance:
    Item
    Specified Condition
    Intake No. 1 journal
    0.085 mm (0.00335 in.)
    Exhaust No. 1 journal
    0.085 mm (0.00335 in.)
    Other journal
    0.085 mm (0.00335 in.)

    Text in Illustration 
    *1
    Plastigage
    *2
    No. 1 Journal
    *3
    Other Journal
    If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing.



9. INSPECT CAMSHAFT THRUST CLEARANCE
  1. Clean the bearing caps, camshaft housing and camshaft journals.

  1. Place the camshafts on the camshaft housing.

  1. Install the camshaft bearing caps .

  1. Install the camshaft housing sub-assembly .



    A259167
  1. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

    Standard Thrust Clearance:
    Item
    Specified Condition
    Intake
    0.060 to 0.155 mm (0.00236 to 0.00610 in.)
    Exhaust
    0.060 to 0.155 mm (0.00236 to 0.00610 in.)

    Maximum Thrust Clearance:
    Item
    Specified Condition
    Intake
    0.170 mm (0.00669 in.)
    Exhaust
    0.170 mm (0.00669 in.)

    If the thrust clearance is more than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.