CYLINDER HEAD > REASSEMBLY |
| 1. INSTALL SPARK PLUG TUBE |
![]() |
Apply adhesive onto the shaded area of a new spark plug tube.
![]() |
Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.
| *a | Cylinder Head Casting Surface |
| 2. INSTALL CYLINDER HEAD STUD BOLT |
![]() |
Using an E7 "TORX" socket wrench, install the 5 cylinder head stud bolts.
| 3. INSTALL NO. 1 STRAIGHT SCREW PLUG |
![]() |
Using a 10 mm hexagon wrench, install 3 new gaskets and the 3 No.1 straight screw plugs.
| 4. INSTALL NO. 2 STRAIGHT SCREW PLUG |
![]() |
Using a 14 mm hexagon wrench, install a new gasket and the No. 2 straight screw plug.
| 5. INSTALL VALVE SPRING SEAT |
Install the valve spring seats to the cylinder head.
| 6. INSTALL VALVE STEM OIL SEAL |
![]() |
Apply a light coat of engine oil to new oil seals.
| *a | Intake |
| *b | Exhaust |
| *c | Mark "NOK" |
| *d | Gray |
| *e | Black |
![]() |
Using SST, push in the intake and exhaust valve oil seals.
| *a | CORRECT |
| *b | INCORRECT |
| 7. INSTALL INTAKE VALVE |

| *A | Type A (Compression Spring Shape: Straight) | *B | Type B (Compression Spring Shape: Tapered) |
| *1 | No. 1 Valve Rocker Arm Sub-assembly | *2 | Valve Spring Retainer |
| *3 | Compression Spring | *4 | Valve Lash Adjuster Assembly |
![]() |
Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.
| *a | 30 mm (1.18 in.) or more |
Type A
Install the 8 intake valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.
![]() |
Using SST and wooden blocks, compress the compression spring and install the 16 valve spring retainer locks.
Type B:
![]() |
Install the 8 intake valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.
| *a | Narrow |
| *b | Wide |
![]() |
Using SST and wooden blocks, compress the compression spring and install the 16 valve spring retainer locks.
![]() |
Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.
| 8. INSTALL EXHAUST VALVE |

| *A | Type A (Compression Spring Shape: Straight) | *B | Type B (Compression Spring Shape: Tapered) |
| *1 | No. 1 Valve Rocker Arm Sub-assembly | *2 | Valve Spring Retainer |
| *3 | Compression Spring | *4 | Valve Lash Adjuster Assembly |
![]() |
Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.
| *a | 30 mm (1.18 in.) or more |
Type A:
Install the 8 exhaust valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.
![]() |
Using SST and wooden blocks, compress the compression spring and install the 16 valve spring retainer locks.
Type B:
![]() |
Install the 8 exhaust valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.
| *a | Narrow |
| *b | Wide |
![]() |
Using SST and wooden blocks, compress the compression spring and install the 16 valve spring retainer locks.
![]() |
Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.