Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REMOVAL

for Preparation Click here



1. REMOVE ENGINE HANGERS


    A264710E01
  1. Remove the 2 bolts and 2 engine hangers.
    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No .2 Engine Hanger



2. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A260233
  1. Remove the engine oil level dipstick.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



3. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A260235
  1. Remove the 4 bolts and No. 1 exhaust manifold heat insulator.



4. DISCONNECT NO. 1 WATER BY-PASS HOSE


    A264717
  1. Disconnect the No. 1 water by-pass hose.



5. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY


    A259034
  1. Disconnect the 2 hoses.



    A259035
  1. Disconnect the throttle body connector.

  1. Disconnect the 2 water by-pass hoses from the throttle with motor body assembly.



    A259045
  1. Remove the 4 bolts and the throttle body with fuel tube bracket.



    A259036
  1. Remove the gasket from the intake manifold.



6. REMOVE MANIFOLD STAY


    A257339
  1. Remove the bolt, nut and manifold stay.



7. REMOVE NO. 2 MANIFOLD STAY


    A257340
  1. Remove the bolt, nut and No. 2 manifold stay.



8. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY


    A195979
  1. Remove the 5 nuts and exhaust manifold converter sub-assembly.



    A195981
  1. Remove the gasket.



9. REMOVE NO. 3 WATER BY-PASS PIPE


    A264182
  1. Disconnect the No. 5 water by-pass hose.



    A264185
  1. Remove the 2 bolts and No. 3 water by-pass pipe.



10. REMOVE NO. 1 WATER BY-PASS PIPE


    A264708E02
  1. Separate the 2 clamps.
    Text in Illustration 
    *1
    Clamp
    *2
    Bolt

  1. Disconnect the No. 4 water by-pass hose and No. 6 water by-pass hose.

  1. Remove the 2 bolts and No. 1 water by-pass pipe.



11. REMOVE COMPRESSOR WITH MOTOR ASSEMBLY


    E230576E02
  1. Disconnect connector B as shown in the illustration.
    Text in Illustration 
    *1
    Green-colored Lock

  1. Release the green-colored lock and disconnect connector A.

    CAUTION:
    Wear insulated gloves when performing the following steps.

    NOTICE:
    Insulate the connector by sealing it with tape.



    E230592
  1. Remove the bolt and 2 nuts.



    E230593
  1. Using an E8 "TORX" socket, remove the 2 stud bolts.



12. REMOVE ENGINE WATER PUMP ASSEMBLY


    A259412
  1. Disconnect the harness clamp.



    A260241
  1. Disconnect the connector from the engine water pump assembly.



    A259348
  1. Remove the 5 bolts and engine water pump assembly.

  1. Remove the gasket from the engine water pump assembly.



13. REMOVE WATER INLET SUB-ASSEMBLY


    A260228
  1. Remove the 2 bolts and water inlet sub-assembly.



    A259352
  1. Remove the gasket from the water inlet sub-assembly.



14. REMOVE WATER INLET HOUSING


    A260229
  1. Remove the bolt and harness clamp bracket from the cylinder block.



    A260227
  1. Remove the bolt and harness clamp bracket from the water inlet housing.



    A260226E01
  1. Remove the 3 bolts, nut, and water inlet housing.
    Text in Illustration 
    *1
    Bolt
    *2
    Nut



    A260225
  1. Remove the gasket.



    A260224
  1. Using an E8 "TORX" socket wrench, remove the stud bolt from the cylinder block.



    A261349
  1. Using an E5 "TORX" socket wrench, remove the stud bolt from the water inlet housing.



15. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET


    A262245
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.



16. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A259321
  1. Disconnect the 4 fuel injector connectors.

  1. Remove the 2 bolts, and then remove the fuel delivery pipe together with the 4 fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe.



    A259322
  1. Remove the 2 fuel delivery spacers from the cylinder head.

  1. Remove the 4 injector vibration insulators from the cylinder head.



17. REMOVE INTAKE MANIFOLD
  1. Remove the intake manifold from the vehicle.



    A257345
  1. Remove the gasket from the intake manifold.



    A257346
  1. Remove the bolt and wire harness clamp bracket.



    A257347
  1. Remove the vacuum hose from the intake manifold.



    A258678
  1. Remove the fuel vapor feed hose from the intake manifold.



18. REMOVE SENSOR WIRE


    A260236
  1. Disconnect the knock control sensor connector.

  1. Remove the bolt and knock control sensor wire.



19. REMOVE IGNITION COIL ASSEMBLY


    A256134
  1. Disconnect the 4 ignition coil assembly connectors.



    A207955
  1. Remove the 4 bolts and 4 ignition coil assemblies.