Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REMOVAL

for Preparation Click here



1. REMOVE ENGINE HANGERS


    A264710E01
  1. Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.
    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger



2. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A260233
  1. Remove the engine oil level dipstick.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



3. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A209579
  1. Remove the 4 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).



4. DISCONNECT NO. 1 WATER BY-PASS HOSE


    A285447
  1. Slide the clamp and disconnect the No. 1 water by-pass hose from the cylinder head sub-assembly.



5. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY


    A259034
  1. Disconnect the 2 hoses.



    A259035
  1. Disconnect the throttle body connector.

  1. Disconnect the 2 water by-pass hoses from the throttle with motor body assembly.



    A259045
  1. Remove the 4 bolts and the throttle body with fuel tube bracket.



    A259036
  1. Remove the gasket from the intake manifold.



6. REMOVE NO. 2 EGR PIPE (w/ EGR System)


    A257338
  1. Remove the 2 bolts, 2 nuts and No. 2 EGR pipe from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and EGR cooler assembly.

  1. Remove the 2 gaskets from the No. 2 EGR pipe.



7. REMOVE NO. 2 MANIFOLD STAY


    A257340
  1. Remove the bolt, nut and No. 2 manifold stay from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly.



8. REMOVE MANIFOLD STAY


    A257339
  1. Remove the bolt, nut and manifold stay from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly.



9. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)


    A195979
  1. Remove the 5 nuts and exhaust manifold converter sub-assembly (TWC: Front Catalyst) from the cylinder head sub-assembly.



    A195981
  1. Remove the gasket from the cylinder head sub-assembly.



10. REMOVE EGR COOLER ASSEMBLY (w/ EGR System)


    A257333
  1. Slide the clamp and disconnect the water by-pass hose from the EGR cooler assembly.



    A260744
  1. Remove the bolt and nut and separate the No. 1 EGR pipe.



    A265183
  1. Slide the 2 clamps and disconnect the No. 4 water by-pass hose and No. 6 water by-pass hose.



    A315145
  1. Remove the bolt, nut and EGR cooler assembly from the cylinder block.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

  1. Remove the gasket from the EGR cooler assembly.



11. REMOVE NO. 1 EGR PIPE (w/ EGR System)


    A285451
  1. Remove the 2 nuts.



    A260230
  1. Remove the 2 bolts, No. 1 EGR pipe and gasket.



12. REMOVE NO. 3 WATER BY-PASS PIPE (w/o EGR System)


    A264182
  1. Slide the clip and disconnect the No. 5 water by-pass hose from the No. 3 water by-pass pipe.



    A264185
  1. Remove the 2 bolts and No. 3 water by-pass pipe.



13. REMOVE NO. 1 WATER BY-PASS PIPE (w/o EGR System)


    A264708E02
  1. Separate the 2 clamps.
    Text in Illustration 
    *a
    Clamp
    *b
    Bolt

  1. Slide the 2 clamps and remove the No. 4 water by-pass hose and No. 6 water by-pass hose from the No. 1 water by-pass pipe.

  1. Remove the 2 bolts and No. 1 water by-pass pipe.



14. REMOVE COMPRESSOR WITH MOTOR ASSEMBLY


    E230576E02
  1. Disconnect connector B as shown in the illustration.
    Text in Illustration 
    *1
    Green-colored Lock

  1. Release the green-colored lock and disconnect connector A.

    CAUTION:
    Wear insulated gloves when performing the following steps.

    NOTICE:
    Insulate the connector by sealing it with tape.



    E230592
  1. Remove the bolt and 2 nuts.



    E230593
  1. Using an E8 "TORX" socket, remove the 2 stud bolts.



15. REMOVE ENGINE WATER PUMP ASSEMBLY


    A259412
  1. Disconnect the harness clamp.



    A260241
  1. Disconnect the engine water pump assembly connector.



    A259348
  1. Remove the 5 bolts and engine water pump assembly.

  1. Remove the gasket from the engine water pump assembly.



16. REMOVE WATER INLET SUB-ASSEMBLY


    A260228
  1. Remove the 2 bolts and water inlet sub-assembly.



    A259352
  1. Remove the gasket from the water inlet sub-assembly.



17. REMOVE WATER INLET HOUSING


    A260229
  1. Remove the bolt and harness clamp bracket from the cylinder block.



    A260227
  1. Remove the bolt and harness clamp bracket from the water inlet housing.



    A260226E02
  1. Remove the 3 bolts, nut and water inlet housing.
    Text in Illustration 
    *a
    Bolt
    *b
    Nut



    A260225
  1. Remove the gasket.



    A260224
  1. Using an E8 "TORX" socket wrench, remove the stud bolt from the cylinder block.



    A261349
  1. Using an E5 "TORX" socket wrench, remove the stud bolt from the water inlet housing.



18. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET


    A262245
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.



19. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A259321
  1. Disconnect the 4 fuel injector connectors.

  1. Remove the 2 bolts, and then remove the fuel delivery pipe together with the 4 fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe.



    A259322
  1. Remove the 2 fuel delivery spacers from the cylinder head.

  1. Remove the 4 injector vibration insulators from the cylinder head.



20. REMOVE INTAKE MANIFOLD
  1. Remove the intake manifold from the cylinder head sub-assembly.



    A257345
  1. Remove the gasket from the intake manifold.



    A257346
  1. Remove the bolt and wire harness clamp bracket from the intake manifold.



    A330827
  1. Disengage the clamp and remove the vacuum hose from the intake manifold.



    A258678
  1. Slide the clip and disconnect the fuel vapor feed hose from the intake manifold.



21. REMOVE SENSOR WIRE


    A260236
  1. Disconnect the knock control sensor connector.

  1. Remove the bolt and knock control sensor wire.



22. REMOVE IGNITION COIL ASSEMBLY


    A256134
  1. Disconnect the 4 ignition coil assembly connectors.



    A207955
  1. Remove the 4 bolts and 4 ignition coil assemblies.