Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL RING PIN

NOTICE:
It is not necessary to remove the ring pin unless it is being replaced.



    A198197E03
  1. Using a plastic-faced hammer, tap in 2 ring pins until they stop.
    Text in Illustration 
    *a
    Protrusion Height

    Standard protrusion height:
    4.3 to 5.3 mm (0.169 to 0.209 in.)



2. INSTALL ENGINE BALANCER ASSEMBLY


    A198170E07
  1. Check that the alignment marks of the balance shaft damper cover and balance shaft driven gear are aligned.
    Text in Illustration 
    *1
    Driven Gear
    *2
    Damper Cover
    *a
    Alignment Mark
    If the alignment marks are not aligned, realign them.



      A198171E07
    1. Place a wrench on the rear cutout part of the No. 2 balance shaft and secure the shaft in place.
      Text in Illustration 
      *1
      Driven Gear
      *2
      Damper Cover
      *a
      Alignment Mark

    2. Rotate the balance shaft driven gear of the No. 1 balance shaft counterclockwise to align the alignment mark of the balance shaft driven gear with the alignment mark of the balance shaft damper cover.



    A196927E01
  1. Install the engine balancer assembly to the stiffening crankcase with the 3 bolts, and tighten the bolts in the sequence shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }



3. INSTALL STUD BOLT

NOTICE:
If a stud bolt is deformed or the threads are damaged, replace it.



  1. Using an E5 and E8 "TORX" socket wrench, install the 3 stud bolts.


    A198166E06


    Text in Illustration 
    *a
    Front Side
    *b
    Lower Side

    Torque:
    for Stud Bolt A:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
    for Stud Bolt B:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



4. INSTALL STIFFENING CRANKCASE ASSEMBLY


    A198168E02
  1. Rotate the crankshaft clockwise so that the crankshaft key is at the position 90° from the bottom as shown in the illustration.
    Text in Illustration 
    *1
    Key



    A260216E01
  1. Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    V100144
    Stiffening Crankcase
    V100146
    Cylinder Block

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard Seal Dimension:
    Area
    Specified Condition
    Continuous Line
    2.5 to 3.5 mm (0.0984 to 0.138 in.)
    Dashed Line
    7.0 to 9.0 mm (0.276 to 0.354 in.) wide and 2.5 to 3.5 mm (0.0984 to 0.138 in.) thick

    Application Length A:
    28 mm (1.10 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes after applying seal packing.
    3. Do not apply oil for at least 2 hours after the installation.



    A198169E03
  1. Check that the rear cutout parts are as shown in the illustration.
    Text in Illustration 
    *a
    Cutout

  1. Clean the bolts and their installation holes.



    A198186E03
  1. Apply adhesive to 3 or more threads of the ends of bolts A.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    Text in Illustration 
    *1
    Adhesive



    A198172E01
  1. Temporarily install the stiffening crankcase with the 11 bolts.

    Bolt Length :
    Item
    Length
    Bolt A
    65 mm (2.56 in.)
    Bolt B
    35 mm (1.38 in.)
    Bolt C
    125 mm (4.92 in.)
    Bolt D
    165 mm (6.50 in.)

    HINT:
    Apply adhesive to bolts A before installation.



    A198172E02
  1. Tighten the 11 bolts in the sequence shown in the illustration to install the stiffening crankcase

    Torque:
    for Bolt A:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }
    except Bolt A:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



5. INSTALL NO. 1 OIL PAN BAFFLE PLATE


    A196920E01
  1. Install the No. 1 oil pan baffle plate and uniformly tighten the 5 bolts in several steps, in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



6. INSTALL OIL STRAINER SUB-ASSEMBLY
  1. Apply a light coat of engine oil to a new gasket.



    A198187E03
  1. Align the protrusion of the gasket with the cutout of the oil strainer, and install the gasket to the oil strainer sub-assembly.
    Text in Illustration 
    *a
    Protrusion

  1. Install the oil strainer sub-assembly with the 3 bolts in several steps, in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



7. INSTALL OIL PAN SUB-ASSEMBLY


    A210205E01
  1. Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.5 to 3.5 mm (0.0984 to 0.138 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes and tighten the bolts and nuts within 10 minutes after applying seal packing.
    3. Do not apply oil for at least 2 hours after the installation.



    A210204E05
  1. Install the oil pan with the 11 bolts and 2 nuts in several steps, in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    *1
    Nut

    HINT:
    Bolt A and nut A are tightened twice.



8. INSTALL OIL PAN DRAIN PLUG
  1. Install a new gasket and oil pan drain plug to the oil pan sub-assembly.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



9. INSTALL OIL FILTER CAP ASSEMBLY
  1. Clean the inside of the oil filter cap, threads and O-ring groove.



    A196675E07
  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    Oil Filter Cap
    *3
    O-ring

  1. Set a new oil filter element into the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.



    A260526E01
  1. Using SST, tighten the oil filter cap.
    Text in Illustration 
    *a
    No Clearance

    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Make sure that the oil filter is installed securely as shown in the illustration.



    A260527E01
  1. Apply a small amount of engine oil to a new O-ring, and install it to the oil filter cap.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

  1. Install the oil filter drain plug.

    Torque:
    13 N*m{ 127 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Be careful that the O-ring does not get caught between any surrounding parts.



10. INSTALL REAR ENGINE OIL SEAL
  1. Apply MP grease to the lip of a new oil seal.

    NOTICE:
    1. Do not allow foreign matter to contact the lip of the oil seal.
    2. Do not allow MP grease to contact the dust seal.



    A195810E01
  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the edges of the cylinder block and crankcase.

    SST
    09223-15030  
    09950-70010   (09951-07150)

    NOTICE:
    1. Keep the lip of the oil seal free from foreign matter.
    2. Do not tap in the oil seal at an angle.



11. INSTALL CYLINDER BLOCK WATER JACKET SPACER


    A196938
  1. Install the cylinder block water jacket spacer to the cylinder block.



12. INSTALL CYLINDER HEAD GASKET


    A259153E01
  1. Clean the cylinder block sub-assembly and cylinder head sub-assembly with solvent.
    Text in Illustration 
    *1
    Cylinder Head Gasket
    *2
    Cylinder Block Sub-assembly
    *a
    Lot No.
    *b
    3.0 mm or more
    *c
    20 mm or more
    V100135
    Seal Packing
    V100136
    Front

  1. Apply a continuous line of seal packing to a new cylinder head gasket as shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard Seal Dimension:
    3.0 to 7.0 mm (0.118 to 0.276 in.) wide and 3.0 mm (0.118 in.) or thicker

    HINT:
    Apply at least 20 mm (0.787 in.) of seal packing from the inside edge of the protrusion of the cylinder block sub-assembly.

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. Place the new cylinder head gasket on the cylinder block sub-assembly surface with the Lot No. stamp facing upward.

    NOTICE:
    Pay attention to the installation direction.



13. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
The cylinder head bolts are tightened in 4 progressive steps.

  1. Place the cylinder head sub-assembly on the cylinder block sub-assembly.

    NOTICE:
    1. Ensure that no oil is on the contact surface of the cylinder head sub-assembly.
    2. Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the gasket with the bottom part of the cylinder head sub-assembly.

  1. Install the 10 plate washers to the 10 cylinder head bolts.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.



  1. Step 1:



      A196908E02
    1. Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts in several steps, in the sequence shown in the illustration.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

      NOTICE:
      Do not drop the plate washers for the cylinder head bolts into the cylinder head sub-assembly.

  1. Step 2:

    1. Tighten the cylinder head bolts again in the sequence shown in the illustration to make sure that they are tightened to the specified torque.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }



  1. Step 3:



      A196910E05
    1. Mark each cylinder head bolt head with paint as shown in the illustration.
      Text in Illustration 
      *a
      Paint Mark
      V100136
      Front

    2. Tighten the cylinder head bolts by 90° in the sequence shown in step 1.

  1. Step 4:

    1. Tighten the cylinder head bolts by another 90° in the sequence shown in step 1.

    2. Check that the paint marks are now facing rearward.

      NOTICE:
      1. Do not add engine oil for at least 2 hours after installation.
      2. Do not start the engine for at least 2 hours after installation.
      3. After installation, if the seal packing has seeped out, wipe it off.

      HINT:
      Perform "Inspection After Repair" after replacing the cylinder head sub-assembly (Click here).



14. INSTALL CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:
It is not necessary to remove the ring pin unless it is being replaced.



    A198195E03
  1. Using a plastic-faced hammer, tap in 10 camshaft bearing cap setting ring pins to the camshaft housing sub-assembly.
    Text in Illustration 
    *a
    Protrusion Height

    Standard protrusion height:
    2.7 to 3.3 mm (0.106 to 0.130 in.)



15. INSTALL STRAIGHT PIN

NOTICE:
It is not necessary to remove the straight pin unless it is being replaced.



    A198194E03
  1. Using a plastic-faced hammer, tap in 2 straight pins to the camshaft housing sub-assembly.
    Text in Illustration 
    *a
    Protrusion Height

    Standard protrusion height:
    5.0 to 7.0 mm (0.197 to 0.276 in.)



16. INSTALL STUD BOLT

NOTICE:
If a stud bolt is deformed or the threads are damaged, replace it.



    A198196E01
  1. Using an E8 "TORX" socket wrench, install the camshaft housing stud bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



17. INSTALL NO. 1 CAMSHAFT BEARING
  1. Clean the No. 1 camshaft bearing.



    A243410E02
  1. Install the No. 1 camshaft bearing to the No. 1 camshaft bearing cap.
    Text in Illustration 
    *1
    Vernier Caliper

  1. Using a vernier caliper, measure the distance between the No. 1 camshaft bearing cap edge and the No. 1 camshaft bearing edge.

    Standard dimension A - B or B - A:
    0 to 0.7 mm (0 to 0.0276 in.)



18. INSTALL NO. 2 CAMSHAFT BEARING
  1. Clean the No. 2 camshaft bearing.



    A198177E04
  1. Install the No. 2 camshaft bearing to the camshaft housing sub-assembly.
    Text in Illustration 
    *1
    Vernier Caliper

  1. Using a vernier caliper, measure the distance between the camshaft housing edge and the No. 2 camshaft bearing edge.

    Standard distance:
    1.15 to 1.85 mm (0.0453 to 0.0728 in.)



19. INSTALL OIL CONTROL VALVE FILTER


    A196915
  1. Install the oil control valve filter to the No. 1 camshaft bearing cap.



20. INSTALL CAMSHAFT
  1. Clean the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.

  1. Apply a light coat of engine oil to the camshaft journal, camshaft housing sub-assembly and camshaft bearing caps.

  1. Install the camshaft and No. 2 camshaft to the camshaft housing sub-assembly.

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft or No. 2 camshaft (Click here).



21. INSTALL CAMSHAFT BEARING CAP


    A259154E02
  1. Confirm the marks and numbers on the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, and 3 No. 3 camshaft bearing caps and place them in their proper positions and directions.



    A259149E04
  1. Install the 11 bolts in the order shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Make sure that the camshaft and No. 2 camshaft rotate smoothly after installing the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 3 No. 3 camshaft bearing caps.



22. INSTALL VALVE STEM CAP
  1. Apply a light coat of engine oil to the valve stem ends.

  1. Install the 16 valve stem caps to the cylinder head sub-assembly.

    NOTICE:
    Do not drop the valve stem caps into the cylinder head sub-assembly.



23. INSTALL VALVE LASH ADJUSTER ASSEMBLY
  1. Inspect the valve lash adjuster assemblies before installing them .

  1. Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

    NOTICE:
    Install each valve lash adjuster assembly to the same place it was removed from.



24. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Apply engine oil to the valve lash adjuster assembly tips and valve stem caps.



  1. Install the 16 No. 1 valve rocker arm sub-assemblies as shown in the illustration.


    A361610E01


    Text in Illustration 
    *A
    Type A
    *B
    Type B
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve Stem Cap
    -
    -



25. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY


  1. Check that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


    A341304E01


    Text in Illustration 
    *A
    Type A
    *B
    Type B
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Stem Cap
    *3
    Valve Lash Adjuster Assembly
    -
    -
    *a
    INCORRECT
    *b
    CORRECT



    A311889E03
  1. Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Dashed Line
    *b
    Groove

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Apply Seal Packing as Follows 
    Area
    Seal Packing Diameter
    Application Position
    Continuous Line
    3.0 to 4.0 mm (0.118 to 0.157 in.)
    Distance from edge of camshaft housing sub-assembly to center of seal packing: 3.5 to 4.0 mm (0.138 to 0.157 in.)
    Dashed Line
    Distance from outside edge of groove to center of seal packing: 2.5 to 3.5 mm (0.0984 to 0.138 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.



    A259156E02
  1. Position the knock pins of the camshaft and No. 2 camshaft as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Approximately 17°
    *b
    Approximately 2°



    A259142E04
  1. Install the camshaft housing sub-assembly, and then install the 20 bolts in the order shown in the illustration.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

    NOTICE:
    1. Do not add engine oil for at least 2 hours after the installation.
    2. Do not start the engine for at least 2 hours after the installation.
    3. After installation, if the seal packing has seeped out, wipe if off.



26. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY


    A200700E09
  1. Check the camshaft timing gear assembly position.
    Text in Illustration 
    *a
    Knock Pin Hole
    *b
    Alignment Mark
    If the camshaft timing gear assembly is not set to the advanced position, release the lock pin and reset the camshaft timing gear assembly (Refer to the "Set Camshaft Timing Gear Assembly" procedure").



    A196901E13
  1. Align and insert the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Pin Hole



    A196904E19
  1. Check that there is no clearance between the camshaft timing gear assembly and camshaft flange.
    Text Illustration 
    *1
    Camshaft Timing Gear Assembly
    *a
    Incorrect
    *b
    Correct
    *c
    Clearance
    *d
    Camshaft Flange
    *e
    No Clearance



    A259408E02
  1. Using a wrench to hold the hexagonal portion of the camshaft, install the bolt.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.
    2. Do not disassemble the camshaft timing gear sub-assembly.

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (Click here).



27. INSTALL CAMSHAFT TIMING SPROCKET


    A259409E02
  1. Using a wrench to hold the hexagonal portion of the No. 2 camshaft, install the camshaft timing sprocket with the bolt.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

    NOTICE:
    Be careful not to damage the cylinder head assembly or spark plug tube with the wrench.



28. INSTALL CRANKSHAFT TIMING SPROCKET


    A196881
  1. Install the crankshaft timing sprocket to the crankshaft.



29. ADD ENGINE OIL


    A259155
  1. Add 50 cc (3.1 cu. in) of engine oil into the oil hole shown in the illustration.

    NOTICE:
    1. Oil must be added if the valve lash adjuster assemblies were removed.
    2. Make sure that the low pressure chamber and oil paths of the valve lash adjuster assemblies are full of engine oil.



30. INSTALL NO. 1 CHAIN VIBRATION DAMPER


    A259139E02
  1. Install the No. 1 chain vibration damper with the 2 bolts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



31. SET NO. 1 CYLINDER TO TDC/COMPRESSION


    A260711E02
  1. Temporarily install the crankshaft pulley bolt.

  1. Rotate the crankshaft 40° counterclockwise to position the crankshaft pulley key as shown in the illustration.



    A259157E02
  1. Check that the timing marks of the camshaft timing gear assembly and camshaft timing sprocket are as shown in the illustration.
    Text in Illustration 
    *a
    Timing Mark
    *b
    Approximately 7°
    *c
    Approximately 32°

    HINT:
    "A" is not a timing mark.



32. INSTALL CHAIN SUB-ASSEMBLY


A343703E01

HINT:
Confirm the color of each mark plate before installing the chain sub-assembly.

Text in Illustration 
*a
for Intake Side
*b
for Exhaust Side
*c
for Crankshaft
Type of Chain Sub-assembly
for Exhaust Side
for Intake Side
for Crankshaft
Type A
Yellow
Yellow
Pink
Type B
Gold
Gold
Gold
Type C
Orange
Orange
Yellow
  1. Place the chain sub-assembly onto the camshaft timing gear assembly, camshaft timing sprocket and crankshaft timing sprocket.

    HINT:
    1. Make sure the mark plate of the chain sub-assembly faces away from the engine.
    2. It is not necessary to install the chain sub-assembly to the teeth of the camshaft timing gear assembly, camshaft timing sprocket and crankshaft timing sprocket.



    A259158E02
  1. Align the mark plate (for Exhaust Side) of the chain sub-assembly with the timing mark of the camshaft timing sprocket and install the chain sub-assembly to the camshaft timing sprocket.
    Text in Illustration 
    *a
    Mark Plate (for Exhaust Side)
    *b
    Timing Mark



    A196872E09
  1. Align the mark plate (for Crankshaft) of the chain sub-assembly with the timing mark of the crankshaft timing sprocket and install the chain sub-assembly to the crankshaft timing sprocket.
    Text in Illustration 
    *a
    Mark Plate (for Crankshaft)
    *b
    Timing Mark



    A196873
  1. Tie a string above the crankshaft timing sprocket so that the chain sub-assembly is secure.



    A259159E02
  1. Using the hexagonal portion of the camshaft, rotate the camshaft counterclockwise with a wrench, align the timing mark of the camshaft timing gear assembly with the mark plate (for Intake Side) of the chain sub-assembly and install the chain sub-assembly to the camshaft timing gear assembly.
    Text in Illustration 
    *a
    Mark Plate (for Intake Side)
    *b
    Timing Mark

    HINT:
    Hold the camshaft in place with a wrench until the No. 1 chain tensioner assembly is installed.



    A259160
  1. Remove the string above the crankshaft timing sprocket, rotate the crankshaft clockwise, and loosen the chain sub-assembly so that the chain tensioner slipper can be installed.

    NOTICE:
    Make sure the chain sub-assembly is secure.



33. INSTALL CHAIN TENSIONER SLIPPER


    A259138
  1. Install the chain tensioner slipper with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



34. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY


    A196877
  1. Install a new gasket and the No. 1 chain tensioner assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Remove the pin from the stopper plate.



35. INSTALL TIMING CHAIN GUIDE


    A259137
  1. Install the timing chain guide with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



36. SET NO. 1 CYLINDER TO TDC/COMPRESSION


    A260711E02
  1. Temporarily install the crankshaft pulley bolt.

  1. Rotate the crankshaft 40° counterclockwise to position the crankshaft pulley key as shown in the illustration.



    A259157E02
  1. Check that the timing marks of the camshaft timing gear assembly and camshaft timing sprocket are as shown in the illustration.
    Text in Illustration 
    *a
    Timing Mark
    *b
    Approximately 7°
    *c
    Approximately 32°

    HINT:
    "A" is not a timing mark.



37. INSTALL TIMING CHAIN COVER PLATE


    A196860
  1. Install a new gasket and the timing chain cover plate with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



38. INSTALL OIL PUMP RELIEF VALVE PLUG


    A196859
  1. Using a 14 mm hexagon wrench, install a new gasket and the oil pump relief valve plug.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



39. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY


    A196858
  1. Apply a light coat of engine oil to 2 new oil pump gaskets and a new oil hole cover gasket.

  1. Install the 2 oil pump gaskets and oil hole cover gaskets to the stiffening crankcase assembly.



    A196862E02
  1. Align the drive rotor spline and the crankshaft timing sprocket as shown in the illustration.
    Text in Illustration 
    *1
    Drive Rotor Spline
    *2
    Crankshaft Timing Sprocket



  1. Apply seal packing in a line to the timing chain cover sub-assembly as shown in the following illustration.


    A196863E11

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.


    Apply Seal Packing as Follows:

    Area
    Seal Packing Diameter (Round)
    Distance from Edge of Cover to Center of Seal Packing
    Seal Packing Application Length
    Seal Pacing Dimension (Flat)
    Dashed Line
    2.5 to 3.5 mm (0.0984 to 0.138 in.)
    2.5 mm (0.0984 in.)
    -
    -
    A - A
    2.5 to 3.5 mm (0.0984 to 0.138 in.)
    2.5 mm (0.0984 in.)
    -
    -
    B - B
    5.0 mm (0.197 in.)
    3.0 mm (0.118 in.)
    28 mm (1.10 in.)
    7.0 mm (0.276 in.) or wider and 3.0 mm (0.118 in.) or thicker
    C - C
    7.0 mm (0.276 in.)
    5.0 mm (0.197 in.)
    25 mm (0.984 in.)
    13.0 mm (0.512 in.) or wider and 3.0 mm (0.118 in.) or thicker
    D - D
    5.0 mm (0.197 in.)
    3.0 mm (0.118 in.)
    26 mm (1.02 in.)
    7.0 mm (0.276 in.) or wider and 3.0 mm (0.118 in.) or thicker
    E
    2.5 to 3.5 mm (0.0984 to 0.138 in.)
    3.0 mm (0.118 in.)
    -
    -

    NOTICE:
    1. Clean the surfaces with non-residue solvent before applying seal packing.
    2. Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
    3. After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.
    4. Do not add engine oil for at least 2 hours after installation.
    5. Do not start the engine for at least 2 hours after installation.



  1. Temporarily install the timing chain cover sub-assembly with the 17 bolts and 2 nuts.


    A232795E04


    Text in Illustration 
    *1
    Nut
    -
    -
    *a
    Torque
    *b
    Tightening Order

    Bolt Length:
    Item
    Length
    Thread Diameter
    Bolt A
    30 mm (1.18 in.)
    8 mm (0.315 in.)
    Bolt B
    35 mm (1.38 in.)
    10 mm (0.394 in.)
    Bolt C
    45 mm (1.77 in.)
    8 mm (0.315 in.)

    NOTICE:
    Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.

  1. Tighten the 17 bolts and 2 nuts in several steps, in the sequence shown in the illustration.

    Torque:
    Bolt A, C, and Nut:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    Bolt B:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }



40. INSTALL ENGINE MOUNTING BRACKET RH


    A259135E01
  1. Install the engine mounting bracket RH with the 5 bolts in the order shown in the illustration.

    Torque:
    Bolt 1, 2 and 3:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }
    Bolt 4 and 5:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.



41. INSTALL TIMING CHAIN COVER OIL SEAL
  1. Apply MP grease to the lip of a new oil seal.

    NOTICE:
    1. Do not allow foreign matter to contact the lip of the oil seal.
    2. Do not allow MP grease to contact the dust seal.



    A195808E01
  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the timing chain cover edge.

    SST
    09223-22010  

    NOTICE:
    1. Keep the lip of the oil seal free from foreign matter.
    2. Do not tap in the oil seal at an angle.



42. INSTALL SPARK PLUG TUBE GASKET


    A259162E01
  1. Tap in the 4 new spark plug tube gaskets to the cylinder head cover sub-assembly.
    Text in Illustration 
    *1
    Spark Plug Tube Gasket
    *2
    Cylinder Head Cover Sub-assembly

    NOTICE:
    1. Do not allow foreign matter to contact the lip of the spark plug tube gasket.
    2. Do not tap in the spark plug tube gasket at an angle.



43. INSTALL STUD BOLT

NOTICE:
If a stud bolt is deformed or the threads are damaged, replace it.



    A260355E01
  1. Using an E6 "TORX" socket wrench, install the 3 stud bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



44. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    A259133
  1. Apply a light coat of engine oil to 2 new gaskets.

  1. Install the 2 gaskets to the camshaft bearing caps.

  1. Install a new gasket to the cylinder head cover sub-assembly.

    NOTICE:
    Remove any oil from the contact surface.



    A259161E01
  1. Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 6.0 mm (0.118 to 0.236 in.)

    Application width A:
    5.0 mm (0.197 in.)

    Text in Illustration 
    *1
    Seal Packing
    *2
    Timing Chain Cover
    *3
    Camshaft Housing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes after applying seal packing.



    A259132E01
  1. Align the cylinder head cover with pin A. Then align the cylinder head cover with pin B and install the cylinder head cover sub-assembly.

  1. Install 3 new seal washers and the 16 bolts, and then tighten the bolts in the order shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not apply oil for at least 2 hours after the installation.



45. INSTALL CRANKSHAFT PULLEY


    A195873E17
  1. Align the pulley set key with the key groove of the crankshaft pulley.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Using SST, hold the crankshaft pulley and install the pulley bolt.

    SST
    09213-54015  
    09330-00021  

    Torque:
    260 N*m{ 2651 kgf*cm , 192 ft.*lbf }

    HINT:
    SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650 (2 pcs)



46. INSTALL CRANKSHAFT POSITION SENSOR
  1. Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.

  1. Install the crankshaft position sensor to the cylinder block sub-assembly with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. If the crankshaft position sensor has been struck or dropped, replace it.
    2. Make sure that the O-ring is not cracked or moved out of place when installing the crankshaft position sensor.

  1. Connect the crankshaft position sensor connector.



47. INSTALL SEPARATOR CASE


    A210188
  1. Apply a light coat of engine oil to a new gasket.

  1. Install the gasket to the separator case.

  1. Install the separator case with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



48. INSTALL VENTILATION CASE SUB-ASSEMBLY


    A210187E01
  1. Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.5 to 3.5 mm (0.0984 to 0.138 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the ventilation case within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.



    A210185E02
  1. Install the ventilation case sub-assembly, and install the 8 bolts and 2 nuts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Do not apply oil for at least 2 hours after the installation.

    HINT:
    Bolt A is tightened twice.



49. INSTALL VENTILATION VALVE SUB-ASSEMBLY
  1. Apply adhesive to 2 or 3 threads of the ventilation valve sub-assembly.

    Adhesive:
    Toyota genuine adhesive 1324, three bond 1324 or equivalent

  1. Using a 19 mm deep socket wrench, install the ventilation valve sub-assembly.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

  1. Install the No. 2 ventilation hose.



50. INSTALL CAMSHAFT POSITION SENSOR
  1. Clean and degrease the threads of the bolt for the camshaft position sensor.



    A158220
  1. Apply a light coat of engine oil to the O-ring of the sensor.

    NOTICE:
    Make sure that the O-ring is not cracked or does not jump out of position during installation.

  1. Install the sensor with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the sensor connector.



51. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A195062E06
  1. Apply a light coat of engine oil to a new O-ring, and install it to the oil control valve.
    Text in Illustration 
    *1
    New O-ring

  1. Install the oil control valve with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
    2. Be careful that the O-ring is not cracked or moved out of place when installing the oil control valve.

  1. Connect the oil control valve connector.



52. INSTALL OIL FILLER CAP GASKET
  1. Install a new oil filler cap gasket to the oil filler cap sub-assembly.



53. INSTALL OIL FILLER CAP SUB-ASSEMBLY
  1. Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.



54. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY


    A085603E15
  1. Apply adhesive to 2 or 3 threads of the oil pressure switch.
    Text in Illustration 
    *1
    Adhesive

    Adhesive:
    TOYOTA Genuine Adhesive 1344, Three Bond 1344 or equivalent.

    NOTICE:
    Do not let adhesive adhere to the oil hole.

  1. Using a 24 mm deep socket wrench, install the oil pressure switch.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine within 1 hour of installation.

  1. Connect the connector.



55. INSTALL ENGINE COOLANT TEMPERATURE SENSOR
  1. Install a new gasket to the engine coolant temperature sensor.

  1. Using a 19 mm ball joint lock nut wrench, install the engine coolant temperature sensor.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Use the torque value compensation formula to calculate the torque value for use when a torque wrench is combined with a tool such as a ball joint lock nut wrench (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
    1. w/ EGR System: (Click here)
    2. w/o EGR System: (Click here)

  1. Connect the engine coolant temperature sensor connector.

  1. Install the wire harness with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the ventilation hose to the cylinder head cover.



56. INSTALL KNOCK CONTROL SENSOR


    A212473E04
  1. Install the sensor with the bolt so that the sensor is angled as shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    Text in Illustration 
    *a
    Front of Engine
    *b
    Up
    *c
    7°
    *d
    10°

    NOTICE:
    The acceptable installation angle of the sensor is between 7° upward and 10° downward from the horizontal position.

    HINT:
    Perform "Inspection After Repair" after replacing the knock control sensor.
    1. w/ EGR System: (Click here)
    2. w/o EGR System: (Click here)

  1. Connect the sensor connector.



57. INSTALL SPARK PLUG
  1. Using a spark plug wrench, install the 4 spark plugs.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Perform "Inspection After Repair" after replacing a spark plug.
    1. w/ EGR System: (Click here)
    2. w/o EGR System: (Click here)



58. INSTALL ENGINE COVER JOINT


    A259127
  1. Install the 3 engine cover joints.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }