Home › Engine / Hybrid System › 2AR-FXE LUBRICATION › OIL PUMP

OIL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY


    A196858
  1. Apply a light coat of engine oil to 2 new oil pump gaskets and a new oil hole cover gasket.

  1. Install the 2 oil pump gaskets and oil hole cover gaskets to the stiffening crankcase assembly.



    A196862E02
  1. Align the drive rotor spline and the crankshaft timing sprocket as shown in the illustration.
    Text in Illustration 
    *1
    Drive Rotor Spline
    *2
    Crankshaft Timing Sprocket



  1. Apply seal packing in a line to the timing chain cover sub-assembly as shown in the following illustration.


    A196863E11

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.


    Apply Seal Packing as Follows:

    Area
    Seal Packing Diameter (Round)
    Distance from Edge of Cover to Center of Seal Packing
    Seal Packing Application Length
    Seal Pacing Dimension (Flat)
    Dashed Line
    2.5 to 3.5 mm (0.0984 to 0.138 in.)
    2.5 mm (0.0984 in.)
    -
    -
    A - A
    2.5 to 3.5 mm (0.0984 to 0.138 in.)
    2.5 mm (0.0984 in.)
    -
    -
    B - B
    5.0 mm (0.197 in.)
    3.0 mm (0.118 in.)
    28 mm (1.10 in.)
    7.0 mm (0.276 in.) or wider and 3.0 mm (0.118 in.) or thicker
    C - C
    7.0 mm (0.276 in.)
    5.0 mm (0.197 in.)
    25 mm (0.984 in.)
    13.0 mm (0.512 in.) or wider and 3.0 mm (0.118 in.) or thicker
    D - D
    5.0 mm (0.197 in.)
    3.0 mm (0.118 in.)
    26 mm (1.02 in.)
    7.0 mm (0.276 in.) or wider and 3.0 mm (0.118 in.) or thicker
    E
    2.5 to 3.5 mm (0.0984 to 0.138in.)
    3.0 mm (0.118 in.)
    -
    -

    NOTICE:
    1. Clean the surfaces with non-residue solvent before applying seal packing.
    2. Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
    3. After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.
    4. Do not add engine oil for at least 2 hours after installation.
    5. Do not start the engine for at least 2 hours after installation.



  1. Temporarily install the timing chain cover sub-assembly with the 17 bolts and 2 nuts.


    A232795E04


    Text in Illustration 
    *1
    Nut
    -
    -
    *a
    Torque
    *b
    Tightening Order

    Bolt Length:
    Item
    Length
    Thread Diameter
    Bolt A
    30 mm (1.18 in.)
    8 mm (0.315 in.)
    Bolt B
    35 mm (1.38 in.)
    10 mm (0.394 in.)
    Bolt C
    45 mm (1.77 in.)
    8 mm (0.315 in.)

    NOTICE:
    Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.

  1. Tighten the 17 bolts and 2 nuts in several steps, in the sequence shown in the illustration.

    Torque:
    Bolt A, C, and Nut:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    Bolt B:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }



2. INSTALL ENGINE MOUNTING BRACKET RH


    A259135E01
  1. Install the engine mounting bracket RH with the 5 bolts in the order shown in the illustration.

    Torque:
    Bolt 1, 2 and 3:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }
    Bolt 4 and 5:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.



3. INSTALL TIMING CHAIN COVER OIL SEAL
  1. Apply MP grease to the lip of a new oil seal.

    NOTICE:
    1. Do not allow foreign matter to contact the lip of the oil seal.
    2. Do not allow MP grease to contact the dust seal.



    A195808E01
  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the timing chain cover edge.

    SST
    09223-22010  

    NOTICE:
    1. Keep the lip of the oil seal free from foreign matter.
    2. Do not tap in the oil seal at an angle.



4. INSTALL CRANKSHAFT PULLEY


    A195873E17
  1. Align the pulley set key with the key groove of the crankshaft pulley.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Using SST, hold the crankshaft pulley and install the pulley bolt.

    SST
    09213-54015  
    09330-00021  

    Torque:
    260 N*m{ 2651 kgf*cm , 192 ft.*lbf }

    HINT:
    SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650 (2 pcs)



5. INSTALL CRANKSHAFT POSITION SENSOR
  1. Clean and degrease the threads of the bolt for the crankshaft position sensor.



    A157503E07
  1. Apply a light coat of engine oil to the O-ring of the sensor.
    Text in Illustration 
    *1
    O-ring



    A192239E06
  1. Apply adhesive to 2 or 3 threads of the bolt.
    Text in Illustration 
    *1
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

  1. Install the sensor with the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    NOTICE:
    Make sure that the O-ring is not cracked or does not jump out of position during installation.

  1. Connect the sensor connector.



6. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    A259133
  1. Apply a light coat of engine oil to 2 new camshaft bearing cap oil hole gaskets.

  1. Install the 2 camshaft bearing cap oil hole gaskets.



    A196889E07
  1. Visually check the spark plug tube gasket.

    OK:
    Area
    Specified Condition
    Upper surface
    No scratches or deformation
    Outer lip
    No scratches or deformation
    Inner lip
    No scratches

    Text in Illustration 
    *a
    Upper Surface
    *b
    Inner Lip
    *c
    Outer Lip
    If the result is not as specified, replace the spark plug tube gasket.

  1. Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

    NOTICE:
    Remove any oil from the contact surface.



    A312340E03
  1. Apply seal packing as shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard Seal Diameter:
    3.0 to 6.0 mm (0.118 to 0.236 in.)

    Text in Illustration 
    *1
    Timing Chain Cover Sub-assembly
    *2
    Camshaft Housing Sub-assembly
    *a
    Application width 5.0 mm (0.197 in.)
    V100135
    Seal packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.



    A195876E03
  1. Align the cylinder head cover sub-assembly with pin (A). Then align the cylinder head cover sub-assembly with pin (B) and install the cylinder head cover sub-assembly.
    Text in Illustration 
    *1
    Seal Washer
    *a
    Pin A
    *b
    Pin B

  1. Install 3 new seal washers and 16 bolts, and then tighten the bolts in the order shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    1. Do not add engine oil for at least 2 hours after installation.



7. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 4 ignition coil assemblies with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    Perform "Inspection After Repair" after replacing an ignition coil assembly.
    1. w/ EGR System: (Click here)
    2. w/o EGR System: (Click here)

  1. Connect the 4 ignition coil assembly connectors.



8. INSTALL ENGINE WIRE


9. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE