Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > OPERATION CHECK

for Preparation Click here



CHECK PANEL & STEERING SWITCH

HINT:
  1. The radio and display receiver assembly panel switches and steering switches are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E268454
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E268513
  5. Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.



  6. E225786E01
  7. Panel & Steering Switch Check Mode
    Screen Description 
    Display
    Content
    *a: Switch condition
    "Pushed" is displayed when any switch is pushed.
    *b: Number of switches pushed
    1. Number of switches pushed at once is displayed.
    2. If more than 3 switches are pushed at once, "More than 3" is displayed.
    3. If 4 or more switches are pushed at once, "More than 3" is displayed.
    *c: Rotary switch direction
    Direction of rotary switch is displayed.

    1. Operate each switch and check that the switch conditions are correctly displayed.

      NOTICE:
      When the "MENU"*1 or "APPS"*2 switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.

      1. *1: w/ DVD Player
      2. *2: w/o DVD Player


CHECK TOUCH SWITCH

HINT:
  1. The touch switches on the screen are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E268454
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E268514
  5. Select "Touch Switch" from the "Function Check/Setting I" screen.



  6. E176521
  7. Touch Switch Check

    1. Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

      HINT:
      1. A "+" mark is displayed where the display is touched.
      2. The "+" mark remains on the display even after your finger is removed.


CHECK MICROPHONE

HINT:
  1. The microphone and microphone input level are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E268454
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E268515
  5. Select "Microphone Check" from the "Function Check/Setting I" screen.



  6. E277821E04
  7. Microphone Check
    Screen Description 
    Display
    Content
    *a: Microphone input level meter
    Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.

    1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.

      HINT:
      The microphone is active at all times when this screen is displayed.


CHECK VEHICLE SIGNAL

HINT:
  1. Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E268454
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E268516
  5. Select "Vehicle Signal" from the "Function Check/Setting I" screen.



  6. E225776
  7. Vehicle Signal Check Mode
    Screen Description 
    Display
    Content
    Battery
    Auxiliary battery voltage is displayed.
    IG
    Power switch ON/OFF state is displayed.
    PKB
    Parking brake ON/OFF state is displayed.
    REV
    Reverse signal ON/OFF state is displayed.
    SPEED
    Vehicle speed is displayed in km/h.
    TAIL
    Tail signal (light control switch) ON/OFF state is displayed.
    ADIM/TCAN
    Brightness state DIM (with)/BRIGHT (without) is displayed.

    HINT:
    1. Only items sending vehicle signals will be displayed.
    2. This screen displays vehicle signals input to the radio and display receiver assembly.
    3. This screen is updated once per second.


    1. When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.


CHECK HANDS-FREE VOICE QUALITY SETTING

HINT:
  1. The hands-free voice quality of a "Bluetooth" compatible phone can be adjusted using the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E268454
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E268517
  5. Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.



  6. E268475E03
  7. Hands-Free Voice Quality Setting
    Text in Illustration 
    *a
    Numeric Keypad
    *b
    Setting Button
    *c
    Reset Button

    1. If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

    2. When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

      Settings 
      Parameter
      Target Phenomenon
      Voice Quality Type
      Positive Effect of Changing Voice Quality
      Negative Effect of Changing Voice Quality
      A
      (Noise)
      The other party hears background noise when listening to your voice.
      1000
      The amount of background noise the other party hears when listening to your voice is reduced.
      The volume of voice the other party hears when listening to your voice may temporarily drop.
      B
      (Noise)
      The other party hears a lot of background noise when listening to your voice.
      2000
      The amount of background noise the other party hears when listening to your voice is sharply reduced.
      The volume of voice the other party hears when listening to your voice may temporarily drop.
      C
      (Echo)
      The other party hears weak echoes.
      0100
      The amount of echo is reduced (low level).
      Sound quality of the other party deteriorates (low level).
      D
      (Echo)
      The other party hears strong echoes.
      0200
      The amount of echo is reduced (high level).
      Sound quality of the other party deteriorates (high level).

      Settings (When Multiple Phenomenon Occurred) 
      Parameter
      Target Phenomenon
      Voice Quality Type
      Positive Effect of Changing Voice Quality
      Negative Effect of Changing Voice Quality
      A+C
      The other party hears background noise and weak echoes when listening to your voice.
      1100
      1. The amount of background noise the other party hears when listening to your voice is reduced.
      2. The amount of echo is reduced (low level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (low level).
      A+D
      The other party hears background noise and strong echoes when listening to your voice.
      1200
      1. The amount of background noise the other party hears when listening to your voice is reduced.
      2. The amount of echo is reduced (high level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (high level).
      B+C
      The other party hears a lot of background noise and weak echoes when listening to your voice.
      2100
      1. The amount of background noise the other party hears when listening to your voice is sharply reduced.
      2. The amount of echo is reduced (low level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (low level).
      B+D
      The other party hears a lot of background noise and strong echoes when listening to your voice.
      2200
      1. The amount of background noise the other party hears when listening to your voice is sharply reduced.
      2. The amount of echo is reduced (high level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (high level).

      HINT:
      1. The default value is "0000".
      2. Settings will be applied when the setting button is selected.
      3. If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.
      4. If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by selecting "INIT".


CHECK SPEAKER

HINT:
  1. This function is used when checking the speaker wiring and whether the speakers are functioning properly.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Turn audio mode on and play any audio source.

    HINT:
    This audio source will be used for the speaker check.

  2. Enter diagnostic mode (Click here).



  3. E268484
  4. Select "Failure Diagnosis" from the "Service Menu" screen.



  5. E268489
  6. Select "System Check" from the "Failure Diagnosis" screen.



  7. E268474
  8. Select "SP Check ON" from the "System Check Mode" screen.

  9. Check the speaker wiring and check that the speakers are functioning properly.

    HINT:
    1. Check that each speaker outputs sound from the selected audio source properly.
    2. "SP Check OFF" is displayed during the speaker check.
    3. Sound can be heard from the speakers around the vehicle in order beginning from a speaker on the front side.
    4. More than one speaker may sound simultaneously depending on the speaker wiring.

  10. Sound stops when any of the following conditions are met:

    1. "SP Check OFF" is selected.

    2. The power switch is turned off.

    3. Diagnostic mode is turned off.

    4. The screen is changed to another screen.

    5. Audio mode is turned off.


CHECK SOFTWARE ERROR HISTORY

HINT:
This function is used to check the cause when the radio and display receiver assembly screen is blacked out.

  1. Check Software Error History.

    1. Connect the GTS to the DLC3.

    2. Turn the power switch to on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.

    5. When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.
      Software Error History Screen Description 
      Error Description
      Trigger
      Detail
      Software Reset
      Navi Microcomputer
      Hexadecimal Number
      Audio Microcomputer
      CAN Microcomputer
      No Video Signal
      Front Monitor
      Rear Monitor
      MOST Cold Restart
      Always

      HINT:
      1. Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.
      2. If an error that is unsupported by the GTS occurs, a "-" is displayed for the display items.

  2. Clear software error history.

    1. When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (Click here).

      1. Cleared using the GTS.
      2. Cleared using the system check mode screen.
      3. Cleared using the unit check mode screen.


CHECK OPTICAL DISC ERROR HISTORY

HINT:
This function is used to check the cause of an optical disc error.

  1. Check Optical Disc Error History.

    1. Connect the GTS to the DLC3.

    2. Turn the power switch to on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.

    5. When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.
      Optical Disc Error History Screen Description 
      Display
      Content
      Error Type
      Displays the type of error.
      Device
      Displays the malfunctioning device.
      Date
      Displays the date and time that the malfunction occurred.
      "Error Type" Screen Description 
      Error Type
      Detection Condition
      Action
      Read Error
      When a disc read error occurs.
      Proceed to next suspected area shown in Problem Symptoms Table (Click here)
      Disc damaged/upside down/dirty
      When it is determined that any of the following is the cause of the disc read error:
      1. The disc cannot be read.
      2. The disc cannot be read because of dirt or scratches.
      3. The disc cannot be read because it is inserted upside down.
      Cannot determine disc type
      An unsuitable disc is inserted.
      DPS error
      When an error occurs while decoding MP3/WMA/AAC files.
      Some files are corrupt
      1. When MP3/WMA/AAC files cannot be played back because they are unsupported.
      2. Even though the file extensions are MP3, WMA or AAC files cannot be played back because the header information cannot be read.
      Some files cannot be found
      1. When a disc without music data is played back.
      2. When there are no playable MP3/WMA/AAC files.
      Copy protection violation
      When a file with copyright protection that cannot be played back is played back.
      "Device" Screen Description 
      Device
      Component
      DVD-P
      Radio and display receiver assembly*1
      CD-P
      Radio and display receiver assembly*2
      R-Seat DVD-P
      Not available

      1. *1: w/ DVD Player
      2. *2: w/o DVD Player

      HINT:
      1. Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.
      2. If an error that is unsupported by the GTS occurs, a "-" or blank is displayed for the display items.

  2. Clear optical disc error history.

    1. When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (Click here).

      1. Cleared using the GTS.
      2. Cleared using the system check mode screen.
      3. Cleared using the unit check mode screen.


CHECK VIDEO DEVICE CONNECTION CHECK

HINT:
  1. This function is used to detect disconnection of the video devices.
  2. In order to inspect the RSE, a disc should be inserted into the radio and display receiver assembly.

  1. Check Video Device Connection Check.

    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.

    5. When an item is stored for Video Device Connection Check, record it before proceeding with troubleshooting.

      HINT:
      1. DTCs are stored when errors are detected.
      2. Depending on the vehicle, some of the items are not displayed on the "Error Detected Image Line (Type)" screen.
        Video Device Connection Check Screen Description 
        Error Detected Image Line (Type)
        Areas to be Checked
        H/U - > Separate Display (GVIF)
        Not available
        H/U - > Full RSE (GVIF)
        Not available
        RSE - > Seat Back Display RH (GVIF)
        Not available
        RSE - > Seat Back Display LH (GVIF)
        Not available
        Rear Camera - > H/U (NTSC)
        NTSC video signal between the radio and display receiver assembly and rear television camera assembly
        IPA/BGM/PVM ECU - > Separate Display (GVIF)
        Not available
        IPA/BGM/PVM ECU - > H/U (NTSC)
        Not available
        IPA/BGM/PVM ECU - > H/U (GVIF)
        Not available

  2. Clear video device connection check.

    1. When DTCs are cleared using any of the following operations, Video Device Connection Check will be cleared as well (Click here).

      1. Cleared using the GTS.
      2. Cleared using the system check mode screen.
      3. Cleared using the unit check mode screen.