Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0C73-776    Motor Electronics Coolant Pump "A" Control Performance

for Preparation Click here


DESCRIPTION

The inverter water pump assembly transmits rotation revolution speed information to the power management control ECU. The power management control ECU monitors the revolution speed and detects malfunctions.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0C73
776
A speed or intermittent stop malfunction occurs in the inverter water pump assembly.
A revolution malfunction (speed is too high/low or stop) or an intermittent stop malfunction (operation stops intermittently when the speed revolution is abnormal) occurs in the inverter water pump assembly.
  1. Inverter cooling system
  2. Wire harness or connector
  3. Inverter water pump assembly
  4. Power management control ECU

HINT:
The inverter water pump assembly operates when the power switch is on (READY).


Related Active Test 
DTC No.
Active Test
P0C73-776
Activate the Water Pump*1
*1: This is an Active Test of the inverter water pump assembly.

WIRING DIAGRAM


A259912E04


INSPECTION PROCEDURE

NOTICE:
  1. If DTC P0A78-284, 286, P0A7A-322, 324, P0A94-553 or 557 is output, replace the inverter with converter assembly after this inspection.
  2. In the case of a coolant leak, the inverter water pump assembly activates a fail-safe function. If the inverter water pump assembly is not the cause of the coolant leak, it is not necessary to replace it.

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (READY) and wait for 120 seconds or more (when the power switch is turned on (READY), the inverter water pump assembly operates).

1.CHECK QUANTITY OF HV COOLANT
  1. Check the HV coolant level in the inverter reserve tank.

  1. Check for HV coolant leaks.
    Result 
    Result
    Proceed to
    No leaks are found and coolant level in the inverter reserve tank assembly is above the low line.
    A
    No leaks are found and coolant level in the inverter reserve tank assembly is below the low line.
    B
    HV coolant leaks are evident.
    C

    HINT:
    After repairing the HV coolant leaks and adding coolant, perform the "Activate the Water Pump" Active Test (HV Active Test item) and the "Control the Electric Cooling Fan" Active Test (Engine Active Test item) and make sure that there are no malfunctions.



B
ADD HV COOLANT

C
INSPECT FOR HV COOLANT LEAK
A


2.CHECK COOLANT HOSE
  1. Check if the hoses of the cooling system are kinked or clogged.



NG
CORRECT THE PROBLEM
OK


3.READ VALUE USING INTELLIGENT TESTER (INVERTER W/P REVOLUTION)

NOTICE:
Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.

HINT:
  1. When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
  2. When the inverter water pump assembly serial communication line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter W/P Revolution.

  1. Read the Data List.

    Result:
    Tester Display
    Switch Condition
    Specified Condition
    Inverter W/P Revolution
    Power switch on (IG)
    625 rpm or less

    HINT:
    When the inverter water pump assembly is not operating, the Data List item "Inverter W/P Revolution" usually displays 625 rpm continuously.

  1. Turn the power switch off.



NG
Go to step 7
OK


4.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP)

NOTICE:
Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.

HINT:
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

  1. Select Inverter W/P Revolution in the Data List.

  1. While performing the "Activate the Water Pump" Active Test, check Inverter W/P Revolution in the Data List.

    Result:
    Tester Display
    Switch Condition
    Specified Condition
    Inverter W/P Revolution
    Power switch on (IG)
    2500 to 5875 rpm

    HINT:
    1. Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).
    2. When the inverter water pump assembly is not operating, the Data List item "Inverter W/P Revolution" usually displays 625 rpm continuously.

  1. Turn the power switch off.



NG
Go to step 7
OK


6.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read the freeze frame data Ambient Temperature using the intelligent tester.

  1. Check if the freeze frame data Ambient Temperature is below freezing.

    Result:
    Result
    Proceed to
    Ambient Temperature value is above freezing temperature of the HV coolant.
    A
    Ambient Temperature value is below freezing temperature of the HV coolant.
    B

    HINT:
    1. HV coolant (SLLC) with a 30% concentration freezes at -15 °C (5°F) and HV coolant (SLLC) with a 50% concentration freezes at -35°C (-31°F).
    2. If the HV coolant freezes in the HV radiator or HV water pump, the coolant temperature in the inverter with converter assembly rises because the HV coolant cannot circulate. As a result, a DTC may be set.
    3. A DTC is set when the water pump impeller cannot rotate due to freezing of the HV coolant.
    4. If a DTC is set due to freezing of HV coolant, the problem cannot be reproduced. Judge whether freezing of HV coolant occurred according to the freeze point of the HV coolant, HV coolant change history and ambient temperature when the DTC was set.

  1. Turn the power switch off.



B
REPLACE HV COOLANT (Click here)
A

REPLACE INVERTER WATER PUMP ASSEMBLY (Click here)  

7.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    A264189
  1. Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (Click here).

    OK:
    The connectors are connected securely and there are no contact pressure problems.



NG
CONNECT SECURELY
OK


8.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)


    A259382
  1. Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (Click here).

    OK:
    The connectors are connected securely and there are no contact pressure problems.



NG
CONNECT SECURELY
OK


9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
  1. Disconnect connector A38 from the power management control ECU.

  1. Disconnect connector A50 from the inverter water pump assembly.



  1. Measure the resistance according to the value(s) in the table below.


    A260030E01


    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    *b
    Front view of wire harness connector
    (to Inverter Water Pump Assembly)

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A50-3 (SWP) - A38-13 (IWP)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    A50-3 (SWP) or A38-13 (IWP) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

  1. Connect the power management control ECU connector.

  1. Connect the inverter water pump assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.READ VALUE USING INTELLIGENT TESTER (INVERTER W/P REVOLUTION)

NOTICE:
Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.

HINT:
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.

  1. Connect the intelligent tester to the DLC3.

  1. Remove the INV W/PMP fuse from the No. 2 engine room relay block.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / ECU Data List / Inverter W/P Revolution.

  1. Read the Data List.

    Result:
    Tester Display
    Switch Condition
    Specified Condition
    Inverter W/P Revolution
    Power switch on (IG)
    125 rpm or less

  1. Turn the power switch off.

  1. Install the INV W/PMP fuse.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
  1. Disconnect connector A38 from the power management control ECU.

  1. Turn the power switch on (IG).



    A204443E20
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A38-13 (IWP) - I3-6 (E1)
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)

    NOTICE:
    Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Connect the power management control ECU connector.



NG
REPLACE INVERTER WATER PUMP ASSEMBLY (Click here)
OK


12.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)
  1. Turn the power switch on (IG).



    A249750E08
  1. While turning the power switch on (IG), check the waveform between the power management control ECU terminals.
    Item
    Content
    Terminal
    A38-13 (IWP) - I3-6 (E1)
    Equipment Setting
    5 V/DIV., 50 ms./DIV.
    Condition
    Power switch on (IG)
    Text in Illustration 
    *a
    Component with Harness Connected
    (Power Management Control ECU)

    OK:
    Waveform duty ratio is between 3% and 9%.

  1. Turn the power switch off.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

REPLACE INVERTER WATER PUMP ASSEMBLY (Click here)