INSTRUMENT PANEL SAFETY PAD > INSTALLATION |
| 1. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY |
Engage the 5 guides and temporarily install the instrument panel safety pad assembly as shown in the illustration.

Install the 2 clips.
Install the 3 bolts <B> and nut <E> or <F>.
Install the 2 passenger airbag bolts <A>.
![]() |
Install the glove box light as shown in the illustration.
Engage each clamp.
Connect each connector.
| 2. CONNECT NO. 2 INSTRUMENT PANEL WIRE |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
![]() |
Connect the connector.
| 3. INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY |
![]() |
Engage the 10 clips to install the No. 1 instrument panel garnish sub-assembly as shown in the illustration.
| 4. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
for LHD:
Connect the connector.
Engage the 3 clips and guide to install the lower instrument panel finish panel assembly.
| 5. INSTALL CONSOLE BOX INSERT |
for RHD:
Engage the 2 claws to connect the room temperature sensor.
![]() |
Engage the clip and 3 guides as shown in the illustration.
Install the console box insert with the 2 screws <C>.
| 6. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
for LHD:
Engage the 2 claws to connect the room temperature sensor.
![]() |
Engage the clip and 3 guides as shown in the illustration.
Install the front No. 2 console box insert with the 2 screws <C>.
| 7. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side) |
| 8. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Engage the 2 guides.
Engage the 3 claws and 2 clips to install the No. 2 instrument panel speaker panel sub-assembly.
| 9. INSTALL FRONT PILLAR GARNISH RH |
| 10. INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY |
Connect the connector.
![]() |
Engage the 6 clips to install the No. 1 speaker opening cover assembly.
| 11. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side) |
Connect the connector.
![]() |
Install the front No. 2 speaker assembly with the 2 screws.
| *A | LH Side |
| *B | RH Side |
| 12. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Engage the 2 guides.
Engage the 3 claws and 2 clips to install the No. 1 instrument panel speaker panel sub-assembly.
| 13. INSTALL FRONT PILLAR GARNISH LH |
Remove the protective cover.
Make sure that the front pillar garnish clip is not damaged.
![]() |
Install the front pillar garnish clip to front pillar garnish LH.
Engage the 2 guides as shown in the illustration.
![]() |
Engage the 2 clips to install the front pillar garnish LH.
| 14. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Engage the 10 clips to install the No. 3 instrument panel register assembly.
| 15. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Engage the 2 clips and 4 guides.
Install the 3 screws <C>.
Close the lower instrument panel door.
Install the lower instrument panel sub-assembly with the bolt <B> and screw <C>.
| 16. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
Connect the connector.
Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.
| 17. INSTALL INSTRUMENT SIDE PANEL RH |
![]() |
Engage the 3 guides as shown in the illustration.
![]() |
Engage the 4 claws to install the instrument side panel RH as shown in the illustration.
| 18. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
| *1 | Alignment Mark (White) |
| 19. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
| 20. INSTALL FRONT DOOR SCUFF PLATE RH |
| 21. INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY |
Connect each connector.
Engage the 6 clips to the vehicle body to temporarily install the radio receiver assembly with air conditioning control assembly.
Install the radio receiver assembly with air conditioning control assembly with the 4 bolts.
| 22. INSTALL FRONT ASH RECEPTACLE ASSEMBLY |
Connect each connector.
![]() |
Engage the 2 clips.
Install the front ash receptacle assembly with the 2 screws <C>.
| 23. INSTALL FRONT CONSOLE UPPER PANEL GARNISH |
Connect each connector.
![]() |
Engage the 2 claws to install the front console upper panel garnish as shown in the illustration.
| 24. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY |
Connect the connector.
![]() |
Engage the 4 clips to install the No. 2 instrument panel register assembly.
| 25. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Engage the 7 clips and 2 guides to install the center instrument cluster finish panel sub-assembly.
| 26. INSTALL CONSOLE BOX ASSEMBLY |
![]() |
Engage the 4 guides as shown in the illustration.
Install the console box assembly with the 2 bolts and 2 screws.
| 27. INSTALL CONSOLE BOX CARPET |
Install the console box carpet.
| 28. INSTALL NO. 4 CONSOLE BOX DUCT |
Engage the claw to install the No. 4 console box duct.
| 29. INSTALL UPPER CONSOLE BOX SUB-ASSEMBLY |
Connect the 2 connectors.
Engage the clamp.
![]() |
Engage the 2 guides and 4 clips as shown in the illustration.
Install the upper console box sub-assembly with the 2 screws.
| 30. INSTALL REAR CONSOLE UPPER PANEL SUB-ASSEMBLY |
Connect each connector.
![]() |
Engage the 6 clips to install the rear console upper panel sub-assembly.
Move the shift lever to P.
| 31. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.
| 32. INSTALL FRONT PANEL GARNISH RH |
![]() |
Engage the 3 clips and 8 guides to install the front panel garnish RH.
| 33. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY |
Engage the 5 clips and 3 guides.
Install the instrument panel sub-assembly with the 2 bolts <B>.
| 34. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
| 35. INSTALL FRONT PANEL GARNISH LH |
![]() |
Engage the 3 clips and 8 guides to install the front panel garnish LH.
| 36. INSTALL COMBINATION METER ASSEMBLY |
Connect the 2 connectors.
Engage the wire harness clamp.
Install the combination meter assembly with the 4 screws.
| 37. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
![]() |
Temporarily install the instrument cluster finish panel assembly as shown in the illustration.
Connect each connector.
for LHD:
Engage the 3 claws, 7 clips and 4 guides.
for RHD:
Engage the 4 claws, 5 clips and 4 guides.
![]() |
Engage the 4 clips and 2 guides to install the instrument cluster finish panel assembly.
| 38. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Engage the 4 clips to install the No. 1 instrument panel register assembly.
| 39. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL (for RHD) |
Connect the connector.
![]() |
Engage the 2 claws and 4 clips to install the upper instrument panel finish panel.
| 40. INSTALL INSTRUMENT SIDE PANEL LH |
![]() |
Engage the 3 guides.
![]() |
Engage the 4 claws to install the instrument side panel LH as shown in the illustration.
| 41. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| *1 | Alignment Mark (Yellow) |
| 42. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Insert the 2 clips in the direction indicated by the arrows shown in the illustration to engage them.
Install the cowl side trim sub-assembly LH with the clip.
| 43. INSTALL FRONT DOOR SCUFF PLATE LH |
Engage the 10 claws to install the front door scuff plate LH.
| 44. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
| 45. INSTALL LUGGAGE TRIM SERVICE HOLE COVER |
Engage the claw to connect the luggage trim service hole cover.
| 46. INSPECT SRS WARNING LIGHT |