INSTRUMENT PANEL SAFETY PAD > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER |
![]() |
Disengage the claw to remove the luggage trim service hole cover.
| 3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
| 4. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.
Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.
Disengage the 6 claws (C) to remove the front door scuff plate LH.
| 5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Remove the clip.
Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 6. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Disconnect the front door opening trim weatherstrip LH.
| 7. REMOVE INSTRUMENT SIDE PANEL LH |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
| 8. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL (for RHD) |
![]() |
Disengage the 2 claws and 4 clips as shown in the illustration.
Disconnect the connector to remove the upper instrument panel finish panel.
| 9. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Disengage the 4 clips to remove the No. 1 instrument panel register assembly as shown in the illustration.
| 10. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.
![]() |
Using a moulding remover, disengage the 4 clips and 2 guides.
for LHD:
![]() |
Disengage the 3 claws, 7 clips and 4 guides.
for RHD:
![]() |
Disengage the 4 claws, 5 clips and 4 guides as shown in the illustration.
Disconnect each connector.
![]() |
Remove the instrument cluster finish panel assembly as shown in the illustration.
| 11. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 4 screws.
![]() |
Disengage the wire harness clamp.
Disconnect the 2 connectors to remove the combination meter assembly.
| 12. REMOVE FRONT PANEL GARNISH LH |
![]() |
Disengage the 3 clips and 8 guides to remove the front panel garnish LH as shown in the illustration.
| 13. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
| 14. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 bolts <B>.
![]() |
Disengage the 5 clips and 3 guides.
Disconnect each connector to remove the instrument panel sub-assembly
| 15. REMOVE FRONT PANEL GARNISH RH |
![]() |
Disengage the 3 clips and 8 guides to remove the front panel garnish RH as shown in the illustration.
| 16. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and disconnect the shift hole cover sub-assembly as shown in the illustration.
![]() |
Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.
| 17. REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY |
Move the shift lever to N.
Disengage the 6 clips as shown in the illustration.

Disconnect each connector to remove the rear console upper panel sub-assembly.
| 18. REMOVE UPPER CONSOLE BOX SUB-ASSEMBLY |
![]() |
Remove the 2 screws.
![]() |
Disengage the 4 clips and 2 guides as shown in the illustration.
![]() |
Disengage the clamp.
Disconnect the 2 connectors to remove the upper console box sub-assembly.
| 19. REMOVE NO. 4 CONSOLE BOX DUCT |
![]() |
Disengage the claw and remove the No. 4 console box duct.
| 20. REMOVE CONSOLE BOX CARPET |
![]() |
Remove the console box carpet.
| 21. REMOVE CONSOLE BOX ASSEMBLY |
![]() |
Remove the 2 bolts and 2 screws.
![]() |
Pull the console box assembly in the direction indicated by the arrow to disengage the 4 guides and remove the console box assembly.
| 22. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Using a moulding remover, pry up on the center instrument cluster finish panel sub-assembly until there is enough of a gap to make it possible to pull on the panel by hand.
![]() |
Pull the center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 7 clips and 2 guides to remove the center instrument cluster finish panel sub-assembly as shown in the illustration.
| 23. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 4 clips as shown in the illustration.
Disconnect the connector to remove the No. 2 instrument panel register assembly.
| 24. REMOVE FRONT CONSOLE UPPER PANEL GARNISH |
![]() |
Disengage the 2 claws as shown in the illustration.
Disconnect each connector to remove the front console upper panel garnish.
| 25. REMOVE FRONT ASH RECEPTACLE ASSEMBLY |
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the 2 clips as shown in the illustration.
Disconnect each connector to remove the front ash receptacle assembly.
| 26. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY |
![]() |
Apply protective tape to the area shown in the illustration.
| *a | Protective Tape |
![]() |
Remove the 4 bolts.
![]() |
Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 6 clips.
Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.
| 27. REMOVE FRONT DOOR SCUFF PLATE RH |
| 28. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
| 29. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Disconnect the front door opening trim weatherstrip RH.
| 30. REMOVE INSTRUMENT SIDE PANEL RH |
![]() |
Using moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.
| 31. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Disengage the 4 claws.
Disengage the 2 guides.
Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.
| 32. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Remove the bolt <B> and screw <C>.
Open the lower instrument panel door.
![]() |
Remove the 3 screws <C>.
![]() |
Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.
| 33. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Using a moulding remover, disengage the 10 clips to remove the No. 3 instrument panel register assembly as shown in the illustration.
| 34. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
| *1 | Front Pillar Garnish Clip |
![]() |
While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.
Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.
![]() |
Protect the curtain shield airbag assembly.
| *1 | Adhesive Tape |
| *2 | Protective Cover |
| *3 | Curtain Shield Airbag Assembly |
Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.
| 35. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Apply protective tape to the areas shown in the illustration.
| *1 | Protective Tape |
![]() |
Using a moulding remover, disengage the 2 clips and 3 claws.
Disengage the 2 guides to remove the No. 1 instrument panel speaker panel sub-assembly.
| 36. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side) |
![]() |
Remove the 2 screws.
![]() |
Lift the front No. 2 speaker assembly and disconnect the connector to remove the speaker.
| 37. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY |
![]() |
Disengage the 6 clips as shown in the illustration.
Disconnect the connector to remove the No. 1 speaker opening cover assembly.
| 38. REMOVE FRONT PILLAR GARNISH RH |
| 39. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Apply protective tape to the areas shown in the illustration.
| *1 | Protective Tape |
![]() |
Using a moulding remover, disengage the 2 clips and 3 claws.
Disengage the 2 guides to remove the No. 2 instrument panel speaker panel sub-assembly.
| 40. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side) |
| 41. REMOVE FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the clip and 3 guides to remove the front No. 2 console box insert as shown in the illustration.
for LHD:
![]() |
Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.
| 42. REMOVE CONSOLE BOX INSERT |
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the clip and 3 guides to remove the console box insert as shown in the illustration.
for RHD:
![]() |
Disengage the 2 claws to disconnect the room temperature sensor from the console box insert.
| 43. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
for LHD:
![]() |
Disengage the 3 clips and guide.
Disconnect the connector to remove the lower instrument panel finish panel assembly.
for RHD:
![]() |
Disengage the 3 clips and guide to remove the lower instrument panel finish panel assembly.
| 44. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY |
Disengage the 10 clips to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.

| 45. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
![]() |
Slide the slider to release the lock, and then disconnect the connector.
| *a | Slider |
| 46. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY |
Disconnect each connector.

| *A | w/ Ion Generator | - | - |
Disengage each clamp.
![]() |
Disconnect the glove box light as shown in the illustration.
Remove the 2 passenger airbag bolts <A>.

| *1 | Passenger Airbag Bolt <A> | *2 | Bolt <B> |
| *3 | Nut <E> or <F> | *4 | Clip |
Remove the 3 bolts <B> and nut <E> or <F>.
Remove the 2 clips.
Disengage the 5 guides and remove the instrument panel safety pad assembly as shown in the illustration.
