Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD

INSTRUMENT PANEL SAFETY PAD > DISASSEMBLY

for Preparation Click here



1. REMOVE NO. 1 INSTRUMENT PANEL PIN


  1. Remove the 4 screws <C> and 4 No. 1 instrument panel pins.


    B281902



2. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

CAUTION:
When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.



    B296281
  1. Remove the 2 screws.



    B296282
  1. Lean the instrument panel safety pad assembly and disengage the 3 hooks.



    B296283
  1. Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad assembly.



3. REMOVE HEATER TO REGISTER DUCT ASSEMBLY (for LHD)


    B281905
  1. Remove the clip.

  1. Remove the 3 screws <C>.

  1. Disengage the heater to register duct assembly from the ion generator assembly, to remove the heater to register duct.



4. REMOVE NO. 1 HEATER TO REGISTER DUCT (for RHD)


    B287345
  1. Remove the clip.

  1. Remove the 3 screws <C> and No. 1 heater to register duct.



5. REMOVE NO. 3 HEATER TO REGISTER DUCT (for LHD)


    B281907
  1. Remove the clip.

  1. Remove the 3 screws <C> and No. 3 heater to register duct.



6. REMOVE HEATER TO REGISTER DUCT ASSEMBLY (for RHD)


    B281904
  1. Remove the clip.

  1. Remove the 3 screws <C>.

  1. Disengage the heater to register duct assembly from the ion generator assembly, to remove the heater to register duct.



7. REMOVE ION GENERATOR SUB-ASSEMBLY WITH BRACKET


    E301559E01
  1. Remove the 3 screws and ion generator sub-assembly with bracket.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD



8. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT


    B277982
  1. Remove the screw <C>.

  1. Disengage the 2 claws to remove the No. 1 side defroster nozzle duct.



9. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT


    B281908
  1. Remove the screw <C>.

  1. Disengage the 2 claws to remove the No. 2 side defroster nozzle duct.



10. REMOVE ANTENNA CORD SUB-ASSEMBLY (for LHD)


  1. Disengage the 8 clamps and remove the antenna cord sub-assembly.


    E226780



11. REMOVE ANTENNA CORD SUB-ASSEMBLY (for RHD)


  1. Disengage the 10 clamps and remove the antenna cord sub-assembly.


    E227950



12. REMOVE DEFROSTER NOZZLE ASSEMBLY


    B277984
  1. Remove the 3 screws <C>.

  1. Disengage the 2 guides to remove the defroster nozzle assembly.



13. REMOVE NO. 2 HEATER TO REGISTER DUCT


    B277985
  1. Remove the 2 screws <C> and No. 2 heater to register duct.



14. REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY


    B277986
  1. Remove the 2 screws <C>.



  1. Apply protective tape to the areas shown in the illustration.


    B281909E01


    Text in Illustration 
    *1
    Protective Tape
    -
    -

  1. Disengage the 6 clips for No. 2 instrument panel garnish sub-assembly lower part as shown in the illustration.

  1. Using a moulding remover, disengage the 8 clips to remove the No. 2 instrument panel garnish sub-assembly as shown in the illustration.