CENTER AIRBAG SENSOR ASSEMBLY > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER |
![]() |
Disengage the claw to remove the luggage trim service hole cover.
| 3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
| 4. REMOVE CONSOLE BOX ASSEMBLY |
| 5. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.
Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.
Disengage the 6 claws (C) to remove the front door scuff plate LH.
| 6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Remove the clip.
Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 7. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 8. REMOVE INSTRUMENT SIDE PANEL LH |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
| 9. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
| 10. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 bolts <B>.
![]() |
Disengage the 5 clips and 3 guides to remove the instrument panel sub-assembly.
| 11. REMOVE FRONT DOOR SCUFF PLATE RH |
| 12. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
| 13. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 14. REMOVE INSTRUMENT SIDE PANEL RH |
![]() |
Using moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.
| 15. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Disengage the 4 claws.
Disengage the 2 guides.
Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.
| 16. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Remove the bolt <B> and screw <C>.
Open the lower instrument panel door.
![]() |
Remove the 3 screws <C>.
![]() |
Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.
| 17. REMOVE FRONT CONSOLE UPPER PANEL GARNISH |
![]() |
Disengage the 2 claws as shown in the illustration.
Disconnect each connector to remove the front console upper panel garnish.
| 18. REMOVE FRONT ASH RECEPTACLE ASSEMBLY |
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the 2 clips as shown in the illustration.
Disconnect each connector to remove the front ash receptacle assembly.
| 19. REMOVE FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the clip and 3 guides to remove the front No. 2 console box insert as shown in the illustration.
for LHD:
![]() |
Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.
| 20. REMOVE CONSOLE BOX INSERT |
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the clip and 3 guides to remove the console box insert as shown in the illustration.
for RHD:
![]() |
Disengage the 2 claws to disconnect the room temperature sensor from the console box insert.
| 21. REMOVE FLOOR CARPET BRACKET LH |
![]() |
Remove the 2 clips.
Disengage the 2 guides to remove the floor carpet bracket LH.
| 22. REMOVE FLOOR CARPET BRACKET RH |
![]() |
Remove the 2 clips.
Disengage the 2 guides to remove the floor carpet bracket RH.
| 23. REMOVE NO. 1 CONSOLE BOX DUCT |
![]() |
Remove the clip and the No. 1 console box duct.
| 24. REMOVE AIRBAG SENSOR ASSEMBLY |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Turn back the carpet.
![]() |
Disconnect the connectors from the airbag sensor assembly as shown in the illustration.
Remove the 3 bolts and airbag sensor assembly.