Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY

CENTER AIRBAG SENSOR ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing (Click here).

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    A259067
  1. Disengage the claw to remove the luggage trim service hole cover.



3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



4. REMOVE CONSOLE BOX ASSEMBLY
(Click here)


5. REMOVE FRONT DOOR SCUFF PLATE LH


    B395175E01
  1. Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.

  1. Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.

  1. Disengage the 6 claws (C) to remove the front door scuff plate LH.



6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B278978
  1. Remove the clip.

  1. Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.



7. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Disconnect the front door opening trim weatherstrip LH to the extent that allows the removal of the instrument side panel LH.



8. REMOVE INSTRUMENT SIDE PANEL LH


    B280320
  1. Using a moulding remover, disengage the 4 claws as shown in the illustration.



    B280322
  1. Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.



9. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B279865
  1. Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.



10. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY


    B384407
  1. Remove the 2 bolts <B>.



    B386777
  1. Disengage the 5 clips and 3 guides.

  1. Disconnect each connector to remove the instrument panel sub-assembly



11. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and LH side .



12. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side .



13. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Disconnect the front door opening trim weatherstrip RH to the extent that allows the removal of the instrument side panel RH.



14. REMOVE INSTRUMENT SIDE PANEL RH


    B281763
  1. Using moulding remover, disengage the 4 claws as shown in the illustration.



    B281765
  1. Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.



15. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B279888
  1. Disengage the 4 claws.

  1. Disengage the 2 guides.

  1. Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.



16. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B281767
  1. Remove the bolt <B> and screw <C>.

  1. Open the lower instrument panel door.



    B281768
  1. Remove the 3 screws <C>.



    B281769
  1. Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.



17. REMOVE FRONT CONSOLE UPPER PANEL GARNISH


    B384411
  1. Disengage the 2 claws as shown in the illustration.

  1. Disconnect each connector to remove the front console upper panel garnish.



18. REMOVE FRONT ASH RECEPTACLE ASSEMBLY


    B384412
  1. Remove the 2 screws <C>.



    B384413
  1. Disengage the 2 clips as shown in the illustration.

  1. Disconnect each connector to remove the front ash receptacle assembly.



19. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    B281774
  1. Remove the 2 screws <C>.



    B281775
  1. Disengage the clip and 3 guides to remove the front No. 2 console box insert as shown in the illustration.



  1. for LHD:



      B280290
    1. Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.



20. REMOVE CONSOLE BOX INSERT


    B281777
  1. Remove the 2 screws <C>.



    B281778
  1. Disengage the clip and 3 guides to remove the console box insert as shown in the illustration.



  1. for RHD:



      B281942
    1. Disengage the 2 claws to disconnect the room temperature sensor from the console box insert.



21. REMOVE FLOOR CARPET BRACKET LH


    E227160
  1. Remove the 2 clips.

  1. Disengage the 2 guides to remove the floor carpet bracket LH.



22. REMOVE FLOOR CARPET BRACKET RH


    E227159
  1. Remove the 2 clips.

  1. Disengage the 2 guides to remove the floor carpet bracket RH.



23. REMOVE NO. 1 CONSOLE BOX DUCT


    E235216
  1. Remove the clip and the No. 1 console box duct.



24. REMOVE AIRBAG SENSOR ASSEMBLY
  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Turn back the carpet.



    B278814
  1. Disconnect the connectors from the airbag sensor assembly as shown in the illustration.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  1. Remove the 3 bolts and airbag sensor assembly.