REAR SEAT OUTER BELT ASSEMBLY > INSTALLATION |
| 1. INSPECT REAR SEAT OUTER BELT ASSEMBLY |
![]() |
Before installing the rear seat outer belt assembly, check the ELR function.
When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.
| *1 | Retractor |
| *a | Unlocked |
| *b | Locked |
| *c | 45° |
| 2. INSTALL REAR SEAT OUTER BELT ASSEMBLY |
Engage the guide to temporarily install the rear seat outer belt assembly.
Install the bolt.
Check if the ELR locks.
With the belt assembly installed, check that the belt locks when it is pulled out quickly.
| 3. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY |
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
![]() |
Engage the 5 guides and 3 clips to install the package tray trim panel assembly.
| 4. INSTALL REAR SEAT SHOULDER BELT COVER |
![]() |
Engage the 4 guides and 2 claws to install the rear seat shoulder belt cover.
| 5. INSTALL CENTER STOP LIGHT SET |
Connect the connector.
Temporarily install the center stop light set.
![]() |
Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to engage the 4 claws.
| 6. INSTALL ROOF SIDE INNER GARNISH LH |
Engage the guide.
Engage the 5 clips to install the roof side inner garnish LH.
| 7. INSTALL ROOF SIDE INNER GARNISH RH |
| 8. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH |
![]() |
Connect the floor anchor of the rear seat inner with center belt assembly LH with the bolt.
| *1 | Protruding Part |
| 9. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH |
Install the child restraint seat anchor bracket sub-assembly LH with the 2 nuts.
| 10. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side) |
![]() |
Connect the floor anchor of the rear seat outer belt assembly with the bolt.
| *1 | Protruding Part |
| 11. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side) |
![]() |
Connect the floor anchor of the rear seat outer belt assembly with the bolt.
| *1 | Protruding Part |
| 12. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
| *1 | Alignment Mark (Red) |
| 13. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
| *1 | Alignment Mark (Blue) |
| 14. INSTALL REAR SEATBACK ASSEMBLY LH |
Place the rear seatback assembly LH in the cabin.
Install the rear seatback assembly LH with the 2 bolts.
![]() |
Engage the fastener as shown in the illustration.
| *1 | Fastener |
Raise the rear seatback assembly LH.
Connect the rear seat outer belt to the rear seat center shoulder belt guide.
| 15. INSTALL REAR SEAT HEADREST ASSEMBLY |
| 16. INSTALL NO. 2 ROOM PARTITION COVER |
![]() |
Engage the guide and claw to install the No. 2 room partition cover.
| 17. INSTALL REAR SIDE SEATBACK ASSEMBLY LH |
Place the rear side seatback assembly LH in the cabin.
Engage the hook to install the rear side seatback assembly LH with the bolt.
Connect the rear seat outer belt to the rear seat shoulder belt guide LH.
| 18. INSTALL REAR SIDE SEATBACK ASSEMBLY RH |
Place the rear side seatback assembly RH in the cabin.
Engage the hook to install the rear side seatback assembly RH with the bolt.
Connect the rear seat outer belt to the rear seat shoulder belt guide RH.
| 19. INSTALL REAR SEAT CUSHION LOCK HOOK |
![]() |
Engage the claw to install a new rear seat cushion lock hook.
| 20. INSTALL REAR SEAT CUSHION ASSEMBLY |
Place the rear seat cushion assembly in the cabin.
![]() |
Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.
Confirm that the rear seat cushion assembly is firmly installed.