REAR SEAT OUTER BELT ASSEMBLY > REMOVAL |
| 1. REMOVE REAR SEAT CUSHION ASSEMBLY |
![]() |
Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
Repeat the step above for the other hook.
Remove the rear seat cushion assembly.
| 2. REMOVE REAR SEAT CUSHION LOCK HOOK |
![]() |
Disengage the claw and remove the rear seat cushion lock hook.
| 3. REMOVE REAR SIDE SEATBACK ASSEMBLY LH |
Disconnect the rear seat outer belt from the rear seat shoulder belt guide LH.
![]() |
Remove the bolt.
Disengage the hook and remove the rear side seatback assembly LH.
| 4. REMOVE REAR SIDE SEATBACK ASSEMBLY RH |
Disconnect the rear seat outer belt from the rear seat shoulder belt guide RH.
![]() |
Remove the bolt.
Disengage the hook and remove the rear side seatback assembly RH.
| 5. REMOVE NO. 2 ROOM PARTITION COVER |
![]() |
Using a moulding remover, disengage the claw and guide, and remove the No. 2 room partition cover.
| 6. REMOVE REAR SEAT HEADREST ASSEMBLY |
| 7. REMOVE REAR SEATBACK ASSEMBLY LH |
Disconnect the rear seat outer belt from the rear seat center shoulder belt guide.
![]() |
Pull the cable in the direction shown in the illustration to release the rear seatback lock and then fold the rear seatback assembly LH forward.
![]() |
Disengage the fastener as shown in the illustration.
| *1 | Fastener |
![]() |
Remove the 2 bolts and rear seatback assembly LH.
| 8. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH |
Disconnect the rear door opening trim weatherstrip LH.
| 9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH |
Disconnect the rear door opening trim weatherstrip RH.
| 10. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side) |
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.
| 11. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side) |
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.
| 12. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH |
![]() |
Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.
| 13. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH |
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.
| 14. REMOVE ROOF SIDE INNER GARNISH LH |
![]() |
Disengage the 5 clips.
Disengage the guide and remove the roof side inner garnish LH.
| 15. REMOVE ROOF SIDE INNER GARNISH RH |
| 16. REMOVE REAR SEAT SHOULDER BELT COVER |
![]() |
Using a moulding remover, disengage the 2 claws and 4 guides and remove the rear seat shoulder belt cover.
| 17. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY |
![]() |
Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.
| *a | Protective Tape |
Disengage the guide.
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.
| 18. REMOVE REAR SEAT OUTER BELT ASSEMBLY |
![]() |
Remove the bolt.
Disengage the guide to remove the rear seat outer belt assembly.