AUDIO AND VISUAL SYSTEM > USB Audio System Recognition/Play Error |

| 1.CHECK USB DEVICE OR "iPod" |
Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.
Check if playable files are present on the USB device or "iPod".
Check if the USB device is a compatible format or "iPod" is a compatible version.
| Result | Proceed to |
| No playable files exist, or incompatible device format or version. | A |
| Playable files exist, and compatible device format or version. | B |
|
| ||||
| A | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY) |
Disconnect the H188 radio and display receiver assembly connector.
Disconnect the I187 No. 1 stereo jack adapter assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I187-1 (UPI) - H188-1 (UPO) | Always | Below 1 Ω |
| I187-2 (UDO-) - H188-2 (UDO-) | Always | Below 1 Ω |
| I187-3 (UDO+) - H188-3 (UDO+) | Always | Below 1 Ω |
| I187-4 (UJSG) - H188-4 (UPSG) | Always | Below 1 Ω |
| I187-5 (UJSS) - H188-5 (USG1) | Always | Below 1 Ω |
| I187-1 (UPI) - Body ground | Always | 10 kΩ or higher |
| I187-2 (UDO-) - Body ground | Always | 10 kΩ or higher |
| I187-3 (UDO+) - Body ground | Always | 10 kΩ or higher |
| I187-4 (UJSG) - Body ground | Always | 10 kΩ or higher |
| I187-5 (UJSS) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Radio and Display Receiver Assembly) |
| *b | Front view of wire harness connector (to No. 1 Stereo Jack Adapter Assembly) |
|
| ||||
| OK | |
| 3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE) |
Disconnect I187 No. 1 stereo jack adapter assembly connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I187-1 (UPI) - I187-4 (UJSG) | Power switch on (ACC) | 5 V |
| *a | Front view of wire harness connector (to No. 1 Stereo Jack Adapter Assembly) |
|
| ||||
| OK | |
| 4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK |
Delete all files in the USB device or "iPod" and format/restore it.
Save the data again and check if it can be played on the in-vehicle device.
|
| ||||
| OK | ||
| ||
| 5.REPLACE USB DEVICE OR "iPod" |
Turn the power switch off.
Turn the power switch on (ACC).
Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.
| NEXT | |
| 6.CHECK USB DEVICE OR "iPod" |
Check if a USB device or "iPod" is recognized by the radio and display receiver assembly, and if information such as track, artist and album names is displayed on the screen.
|
| ||||
| OK | ||
| ||