ROOF HEADLINING > REASSEMBLY |
| 1. INSTALL NO. 1 ROOF WIRE |
Apply double-sided tape as shown in the illustration.

| *A | w/o Sliding Roof | *B | w/ Sliding Roof |
| *C | Tape Attachment Locations (Reference) | - | - |
| *1 | Double-sided Tape | *2 | Marking |
Peel off the release paper from the double-sided tape.
Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.
Align the pink marking tape (A) on the No. 1 roof wire with the vehicle front side tab on the roof headlining.

| *A | w/o Sliding Roof | *B | w/ Sliding Roof |
| *1 | Pink Marking Tape (A) | *2 | Pink Marking Tape (B) |
| *3 | Pink Marking Tape (C) | *4 | Marking |
| *5 | Adjustment Area | - | - |
Turn the visor connector LH clockwise approximately 45° to install it to the roof headlining assembly.
Align the edge of the pink marking tape (A) on the No. 1 roof wire with the markings on the roof headlining.
Attach the No. 1 roof wire, starting from the pink marking tape (B) to the pink marking tape (A) while aligning it with the double-sided tape.
Turn the visor connector RH clockwise approximately 45° to install it to the roof headlining assembly.
Attach the No. 1 roof wire, starting from the visor connector RH to the pink marking tape (B) while aligning it with the double-sided tape.
Align the edge of the pink marking tape (C) on the No. 1 roof wire with the markings on the roof headlining.
Attach the No. 1 roof wire, starting from the pink marking tape (A) to the pink marking tape (C) while aligning it with the double-sided tape.
Apply adhesive tape by aligning it with the markings on the roof headlining as shown in the illustration.

| *A | w/o Sliding Roof | *B | w/ Sliding Roof |
| *C | Tape Attachment Location (Reference) | *D | for LHD |
| *E | for RHD | - | - |
| *1 | Adhesive Tape | *2 | Marking |
| 2. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY |
Apply new double-sided tape.

| *A | w/o Sliding Roof | *B | w/ Sliding Roof |
| *1 | Double-sided Tape | - | - |
| *a | Front | *b | Double-sided Tape Size |
| Area | Dimension |
| A | 1.0 mm (0.0394 in.) |
| B | 10.0 mm (0.394 in.) |
Remove the old double-sided tape from the roof headlining assembly.
Prepare the appropriate amount of new double-sided tape.
Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.
Peel off the release paper from the double-sided tape.
Install the No. 2 antenna cord sub-assembly to the roof headlining assembly from the front of the vehicle.

| *A | w/o Sliding Roof | *B | w/ Sliding Roof |
| *1 | Double-sided Tape | *2 | Tape |
| *3 | Marking Tape | *4 | Protrusion |
| *5 | Adjustment Area | - | - |
| *a | Front | - | - |
Put the pieces of tape back to the positions shown in the illustration in order to secure the antenna cord to the roof headlining assembly.
| 3. INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof) |
Align the markings on the roof headlining assembly with the No. 2 roof silencer pad and install the pad using hot-melt glue as shown in the illustration.

| *1 | Marking | *2 | Hot-melt Glue |
| 4. INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof) |
Align the markings on the roof headlining assembly with the 3 No. 4 roof silencer pads and install the pads using hot-melt glue as shown in the illustration.

| *1 | Marking | *2 | Hot-melt Glue |
| 5. INSTALL VANITY LIGHT ASSEMBLY |
Install the vanity light assembly .