BRAKE BOOSTER PUMP (for LHD) > INSTALLATION |
| 1. INSTALL BRAKE BOOSTER PUMP ASSEMBLY |
![]() |
Insert the stud of the brake booster pump assembly to the hole of the brake actuator bracket assembly, and insert the 2 pins of the brake actuator bracket assembly to the 2 brake booster pump bushings (*5).
| *1 | Union |
| *2 | Stud |
| *3 | Connector Box and Wire Harness |
| *4 | Pin |
| *5 | Brake Booster Pump Bushing |
| *6 | Brake Booster Pump Collar |
| *7 | Brake Actuator Case Collar |
| *8 | Brake Booster Pump Bushing |
Install the brake actuator case collar (*7), brake booster pump bushing (*8) and brake booster pump assembly to the brake actuator bracket assembly with the nut.
Engage the wire harness clamp to the brake actuator bracket assembly.
| 2. INSTALL NO. 1 BRAKE ACTUATOR HOSE |
![]() |
Install the No. 1 brake actuator hose to the brake booster pump assembly with the clip.
![]() | Up |
| 3. INSTALL BRAKE BOOSTER PUMP ASSEMBLY WITH BRACKET |
![]() |
Engage the claw to set the brake booster pump assembly with bracket to the vehicle body.
| *a | Claw |
Install the 3 bolts to secure the brake booster pump assembly with bracket to the vehicle body.
![]() |
Engage the claw to set the connector box to the brake actuator bracket assembly.
| *1 | Connector Box |
| *a | Claw |
Install the bolt to secure the connector box to the brake actuator bracket assembly.
Connect the 2 connectors to the brake booster pump assembly.
| 4. CONNECT FRONT NO. 1 BRAKE TUBE |
Using a union nut wrench, connect the front No. 1 brake tube to the brake booster pump assembly.
| 5. CONNECT NO. 1 BRAKE ACTUATOR HOSE |
![]() |
Connect the No. 1 brake actuator hose to the No. 1 brake actuator tube with the clip.
![]() | Up |
| 6. BLEED NO. 1 BRAKE ACTUATOR TUBE |
Add brake fluid into the brake master cylinder reservoir assembly.
![]() |
Lift up the brake master cylinder reservoir assembly as far as possible and rock it back and forth to bleed air from the reservoir tube assembly.
| *1 | No. 1 Brake Actuator Tube |
| 7. INSTALL NO. 1 BRAKE ACTUATOR TUBE |
Install the No. 1 brake actuator tube to the vehicle body with the nut.
Install the nut and engage the clamp.
| 8. INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY |
Install the brake master cylinder reservoir assembly to the reservoir bracket with the 2 bolts.
| 9. INSTALL SUCTION PIPE SUB-ASSEMBLY |
Remove the vinyl tape from the openings of the disconnected parts.
Sufficiently apply compressor oil to a new O-ring, the fitting surface of the suction pipe sub-assembly and air conditioning unit.
Install the O-ring to the suction pipe sub-assembly.
![]() |
Insert the suction pipe sub-assembly to the air conditioning unit.
| 10. INSTALL AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
Remove the vinyl tape from the openings of the disconnected parts.
Sufficiently apply compressor oil to a new O-ring, the fitting surface of the air conditioning tube and accessory assembly and air conditioning unit.
Install the O-ring to the air conditioning tube and accessory assembly.
![]() |
Insert the air conditioning tube and accessory assembly to the air conditioning unit.
Turn the hook connector and install the bolt.
| 11. FILL RESERVOIR WITH BRAKE FLUID |
| 12. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
| 13. BLEED BRAKE SYSTEM |
Remove the front outer cowl top panel sub-assembly.
Bleed the brake system.
![]() |
Wait at least 2 minutes with the power switch off, and disconnect the reservoir level switch connector.
| *A | for LHD |
| *B | for RHD |
![]() |
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid into the reservoir between the MAX and MIN level on the brake fluid reservoir.
Connect the intelligent tester to the DLC3 and turn the power switch on (IG).
Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.
Select "ABS actuator has been replaced" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.
![]() |
After air bleeding, tighten each bleeder plug.
| *1 | Stroke Simulator Bleeder Plug |
Clear the DTCs (Click here).
Turn the intelligent tester off and turn the power switch off.
Install the brake master cylinder reservoir filler cap.
Inspect for brake fluid leaks.
Install the outer cowl top panel sub-assembly.
| 14. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Insert the projection of the air cleaner case sub-assembly to the hole of the No. 2 air cleaner bracket as shown in the illustration.
| *a | Projection |
Tighten the 2 bolts.
| 15. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| 16. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
Install the air cleaner hose with the hose clamp.
![]() |
Connect the 2 fuel vapor feed hoses.
| *1 | Retainer |
| *a | Push |
Install the air cleaner cap sub-assembly with the 2 clamps.
Connect the connector.
Connect the ventilation hose to the cylinder head cover.
Connect the mass air flow meter connector and wire harness clamp to the air cleaner cap sub-assembly.
| 17. INSTALL INLET AIR CLEANER ASSEMBLY |
Install the inlet air cleaner with the 2 bolts.
| 18. INSTALL COOL AIR INTAKE DUCT SEAL |
Install the cool air intake duct seal with the 9 clips.
| 19. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump or appropriate equipment.
Charge the air conditioning system with refrigerant.

| *a | Sub-cool System | *b | High Pressure |
| *c | Refrigerant Amount | *d | Standard charge amount |
| *e | Charge additional 100 g (3.5 oz.) | *f | Point where bubbles disappear |
| *g | Mean value in proper range | *h | Overcharged |
| 20. WARM UP COMPRESSOR |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 21. INSPECT FOR REFRIGERANT LEAK |
After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
| *1 | Halogen Leak Detector |
| *a | Inspect for Leak |
![]() |
Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
| *1 | Halogen Leak Detector |
| *2 | Drain Hose |
If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.
Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.
| 22. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY |
Install the front outer cowl top panel sub-assembly with the 10 bolts.
Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.
| 23. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |