Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP (for RHD)

BRAKE BOOSTER PUMP (for RHD) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE ACTUATOR BRACKET ASSEMBLY


    C243039E01
  1. Engage the claw to set the brake actuator bracket assembly to the vehicle body.
    Text in Illustration 
    *a
    Claw

  1. Install the 3 bolts to secure the brake actuator bracket assembly to the vehicle body.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Tighten the 3 bolts in the order shown in the illustration.

  1. Engage the clamp to install the front No. 5 brake tube to the brake actuator bracket assembly.

  1. Engage the 2 clamps to install the 2 wire harnesses to the brake actuator bracket assembly.



2. INSTALL FRONT WHEEL LH

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }



3. INSTALL BRAKE BOOSTER PUMP ASSEMBLY


    C243035E01
  1. Insert the 2 studs of the brake booster pump assembly to the 2 holes of the brake actuator bracket assembly, and insert the pin of the brake actuator bracket assembly to the brake booster pump bushing.
    Text in Illustration 
    *1
    Union
    *2
    Connector
    *3
    Stud
    *4
    Pin
    *5
    Brake Booster Pump Bushing
    *6
    Brake Booster Pump Collar

    NOTICE:
    1. Do not carry the brake booster pump assembly by the parts shown in bold (*1, *2 and *3) in the illustration.
    2. Do not drop the brake booster pump assembly when carrying it.
    3. Do not kink or damage the brake lines.
    4. Be careful not to allow any brake fluid to enter the connector.
    5. When installing the brake booster pump assembly to the brake actuator bracket assembly, confirm that the brake booster pump collar and brake booster pump bushing are installed on the brake booster pump assembly.
    6. Do not remove the hole plugs before installing a new brake booster pump assembly because the brake booster pump assembly is filled with brake fluid.

  1. Install the 2 brake actuator case collars, 2 brake booster pump bushings and 2 nuts to the brake actuator bracket assembly.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Using a union nut wrench, connect the front No. 1 brake tube to the brake booster pump assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).

  1. Connect the 2 connectors to the brake booster pump assembly.



4. INSTALL RESERVOIR BRACKET


    C243030E01
  1. Engage the claw to set the reservoir bracket to the brake actuator bracket assembly.
    Text in Illustration 
    *a
    Claw

  1. Install the 2 bolts to secure the reservoir bracket to the brake actuator bracket assembly.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



5. CONNECT NO. 1 BRAKE ACTUATOR HOSE


    C243058E01
  1. Connect the No. 1 brake actuator hose to the brake booster pump assembly with the clip.
    Text in Illustration 
    V100136
    Up

    NOTICE:
    1. When connecting the No. 1 brake actuator hose, face the identification mark up.
    2. Match the identification mark of the No. 1 brake actuator hose and the rib of the brake booster pump assembly.
    3. Make sure to install the hose to the proper location.
    4. Install the clip within the range shown in the illustration.



6. BLEED RESERVOIR TUBE
  1. Add brake fluid into the brake master cylinder reservoir assembly.



    C243024E01
  1. Lift up the brake master cylinder reservoir assembly as far as possible and rock it back and forth to bleed air from the reservoir tube assembly.
    Text in Illustration 
    *1
    Reservoir Tube

    NOTICE:
    1. Do not damage the hoses or tubes.
    2. Do not spill the brake fluid.
    3. Continue this procedure until only a minor amount of air remains in the brake actuator tube.



7. INSTALL RESERVOIR TUBE
  1. Install the reservoir tube to the vehicle body with the 2 bolts and nut.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



8. INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
  1. Install the brake master cylinder reservoir assembly to the reservoir bracket with the 2 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Engage the wire harness clamp.



9. FILL RESERVOIR WITH BRAKE FLUID


10. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL



11. BLEED BRAKE SYSTEM
  1. Remove the front outer cowl top panel sub-assembly.

    1. for LHD: Click here
    2. for RHD: Click here



  1. Bleed the brake system.



      C245585E01
    1. Wait at least 2 minutes with the power switch off, and disconnect the reservoir level switch connector.
      Text in Illustration 
      *A
      for LHD
      *B
      for RHD

      NOTICE:
      Do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.

      HINT:
      This procedure is not required if the reservoir level switch connector has been disconnected.



    2. C239900
    3. Remove the brake master cylinder reservoir filler cap assembly.

    4. Add brake fluid into the reservoir between the MAX and MIN level on the brake fluid reservoir.

      Brake fluid:
      SAE J1703 or FMVSS No. 116 DOT3

    5. Connect the intelligent tester to the DLC3 and turn the power switch on (IG).

    6. Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.

    7. Select "ABS actuator has been replaced" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.

      NOTICE:
      Before following the instructions on the intelligent tester to perform linear valve offset calibration, release the parking brake. When calibration is complete, immediately apply the parking brake.



    8. C209151E01
    9. After air bleeding, tighten each bleeder plug.

      Torque:
      disc brake cylinder bleeder plug:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      stroke simulator bleeder plug:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      HINT:
      The stroke simulator bleeder plug is positioned as shown in the illustration.

      Text in Illustration 
      *1
      Stroke Simulator Bleeder Plug

    10. Clear the DTCs (Click here).

    11. Turn the intelligent tester off and turn the power switch off.

  1. Install the brake master cylinder reservoir filler cap.

  1. Inspect for brake fluid leaks.

  1. Install the outer cowl top panel sub-assembly.

    1. for LHD: Click here
    2. for RHD: Click here



12. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A259768E03
  1. Insert the projection of the air cleaner case sub-assembly to the hole of the No. 2 air cleaner bracket as shown in the illustration.
    Text in Illustration 
    *a
    Projection

  1. Tighten the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



13. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


14. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner hose with the hose clamp.



    A259685E01
  1. Connect the 2 fuel vapor feed hoses.
    Text in Illustration 
    *1
    Retainer
    *a
    Push

    NOTICE:
    1. Check that there are no scratches or foreign matter around the connected part of the fuel tube connector and pipe before performing this work.
    2. Connect the quick connector and push the retainer in until the retainer makes a "click" sound to lock the claws of the retainer.
    3. After connecting the fuel vapor feed hose to the fuel tube connector, check that the fuel vapor feed hose is securely connected by pulling on the fuel tube connector and the fuel vapor feed hose.

  1. Install the air cleaner cap sub-assembly with the 2 clamps.

  1. Connect the connector.

  1. Connect the ventilation hose to the cylinder head cover.

  1. Connect the mass air flow meter connector and wire harness clamp to the air cleaner cap sub-assembly.



15. INSTALL INLET AIR CLEANER ASSEMBLY
  1. Install the inlet air cleaner with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



16. INSTALL COOL AIR INTAKE DUCT SEAL
  1. Install the cool air intake duct seal with the 9 clips.



17. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY
  1. Install the front outer cowl top panel sub-assembly with the 10 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.



18. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY