Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP (for LHD)

BRAKE BOOSTER PUMP (for LHD) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM
  1. Turn the power switch on (READY).

  1. Turn the A/C switch on.

  1. Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.

  1. Turn the power switch off.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.



3. DISABLE BRAKE CONTROL
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C239901
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



4. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


5. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY


    C239198
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel subassembly.



    C239185
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



6. REMOVE COOL AIR INTAKE DUCT SEAL


    B379695
  1. Remove the 9 clips and cool air intake duct seal.



7. REMOVE INLET AIR CLEANER ASSEMBLY


    A259747
  1. Remove the 2 bolts and inlet air cleaner assembly.



8. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A259032
  1. Disconnect the mass air flow meter connector and wire harness clamp from the air cleaner cap sub-assembly.

  1. Disconnect the ventilation hose from the cylinder head cover.

  1. Disconnect the connector.



    A259031
  1. Release the 2 clamps and remove the air cleaner cap sub-assembly.



    A259684E01
  1. Disconnect the 2 fuel vapor feed hoses.
    Text in Illustration 
    *1
    Retainer
    *2
    Fuel Tube Connector
    *3
    Pipe
    *4
    O-ring
    *a
    Pull

    NOTICE:
    1. Remove any dirt or foreign matter on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel vapor feed hose.



    A259033
  1. Loosen the hose clamp and disconnect the air cleaner hose from the throttle with motor body assembly.



9. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


10. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A259768E03
  1. Remove the 2 bolts and air cleaner case sub-assembly.
    Text in Illustration 
    *a
    Projection



11. SEPARATE AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY


    C239871
  1. Remove the bolt from the hook connector.



    C239872
  1. Turn the hook connector and separate the air conditioning tube and accessory assembly from the air conditioning unit.

    NOTICE:
    1. Do not deform the piping.
    2. Do not damage the plastic clamp.

  1. Remove the O-ring from the air conditioning tube and accessory assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



12. SEPARATE SUCTION PIPE SUB-ASSEMBLY


    C239875
  1. Separate the suction pipe sub-assembly from the air conditioning unit.

    NOTICE:
    1. Do not deform the piping.
    2. Do not damage the plastic clamp.

  1. Remove the O-ring from the suction pip sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



13. DRAIN BRAKE FLUID

NOTICE:
If brake fluid leaks onto any painted surface, immediately clean it off.



14. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY


    C242702
  1. Remove the 2 bolts and brake master cylinder reservoir assembly.



15. SEPARATE NO. 1 BRAKE ACTUATOR TUBE


    C242704
  1. Remove the nut and disengage the clamp.



    C242703
  1. Remove the nut and separate the No. 1 brake actuator tube from the vehicle body.



16. DISCONNECT NO. 1 BRAKE ACTUATOR HOSE


    C242715
  1. Move the clip and disconnect the No. 1 brake actuator hose from the No. 1 brake actuator tube.



17. DISCONNECT FRONT NO. 1 BRAKE TUBE


    C242716
  1. Using a union nut wrench, disconnect the front No. 1 brake tube from the brake booster pump assembly.



18. REMOVE BRAKE BOOSTER PUMP ASSEMBLY WITH BRACKET


    C242713
  1. Disconnect the 2 connectors from the brake booster pump assembly.



    C242714E01
  1. Remove the bolt and separate the connector box of the brake booster pump assembly from the brake actuator bracket assembly.
    Text in Illustration 
    *1
    Connector Box



    C242717
  1. Remove the 3 bolts and brake booster pump assembly with bracket from the vehicle body.

    NOTICE:
    Do not kink or damage the brake line, suction pipe sub-assembly or air conditioning tube and accessory assembly.



19. REMOVE NO. 1 BRAKE ACTUATOR HOSE


    C242718
  1. Move the clip and remove the No. 1 brake actuator hose from the brake booster pump assembly.



20. REMOVE BRAKE BOOSTER PUMP ASSEMBLY


    C242719
  1. Disengage the wire harness clamp from the brake actuator bracket assembly.



    C242720E01
  1. Remove the nut, brake actuator case collar, brake booster pump bushing and brake booster pump assembly from the brake actuator bracket assembly.
    Text in Illustration 
    *1
    Union
    *2
    Stud
    *3
    Connector Box and Wire Harness

    NOTICE:
    1. Do not carry the brake booster pump assembly by the parts shown in bold (*1, *2 and *3) in the illustration.
    2. Do not drop the brake booster pump assembly when carrying it.
    3. Do not kink or damage the brake line.
    4. Be careful not to allow any brake fluid to enter the connector.