BRAKE BOOSTER PUMP (for RHD) > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 3. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY |
![]() |
Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.
![]() |
Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.
![]() |
Remove the 10 bolts and front outer cowl top panel sub-assembly.
| 4. DISABLE BRAKE CONTROL |
Wait at least 2 minutes after turning the power switch off.
![]() |
Disconnect the reservoir level switch connector with the parking brake applied.
Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).
Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
Check that the brake pedal can not be further depressed.
Release the parking brake.
| 5. DRAIN BRAKE FLUID |
| 6. REMOVE COOL AIR INTAKE DUCT SEAL |
![]() |
Remove the 9 clips and cool air intake duct seal.
| 7. REMOVE INLET AIR CLEANER ASSEMBLY |
![]() |
Remove the 2 bolts and inlet air cleaner assembly.
| 8. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the mass air flow meter connector and wire harness clamp from the air cleaner cap sub-assembly.
Disconnect the ventilation hose from the cylinder head cover.
Disconnect the connector.
![]() |
Release the 2 clamps and remove the air cleaner cap sub-assembly.
![]() |
Disconnect the 2 fuel vapor feed hoses.
| *1 | Retainer |
| *2 | Fuel Tube Connector |
| *3 | Pipe |
| *4 | O-ring |
| *a | Pull |
![]() |
Loosen the hose clamp and disconnect the air cleaner hose from the throttle with motor body assembly.
| 9. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| 10. REMOVE AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and air cleaner case sub-assembly.
| *a | Projection |
| 11. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY |
![]() |
Disengage the clamp of the wire harness.
Remove the 2 bolts and separate the brake master cylinder reservoir assembly from the reservoir bracket.
| 12. SEPARATE RESERVOIR TUBE |
![]() |
Remove the 2 bolts and nut, and separate the reservoir tube from the vehicle body.
| 13. DISCONNECT NO. 1 BRAKE ACTUATOR HOSE |
![]() |
Move the clip and disconnect the No. 1 brake actuator hose from the brake booster pump assembly.
| 14. REMOVE RESERVOIR BRACKET |
![]() |
Remove the 2 bolts and reservoir bracket from the brake actuator bracket assembly.
| 15. REMOVE BRAKE BOOSTER PUMP ASSEMBLY |
![]() |
Disconnect the 2 connectors from the brake booster pump assembly.
![]() |
Using a union nut wrench, disconnect the front No. 1 brake tube from the brake booster pump assembly.
![]() |
Remove the 2 nuts, brake booster pump assembly, 2 brake actuator case collars and 2 brake booster pump bushings from the brake actuator bracket assembly.
| *1 | Union |
| *2 | Connector |
| *3 | Stud |
| 16. REMOVE FRONT WHEEL LH |
| 17. REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY |
![]() |
Disengage the 2 clamps to separate the 2 wire harnesses from the brake actuator bracket assembly.
![]() |
Disengage the clamp to separate the front No. 5 brake tube from the brake actuator bracket assembly.
![]() |
Remove the 3 bolts and brake actuator bracket assembly from the vehicle body.