Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM

FRONT LOWER SUSPENSION ARM > INSTALLATION

for Preparation Click here



1. INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for LH Side)
  1. Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly LH.



    C167143E01
  1. Install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

    Torque:
    Bolt 1, 2:
    200 N*m{ 2039 kgf*cm , 148 ft.*lbf }
    Bolt 3:
    135 N*m{ 1377 kgf*cm , 100 ft.*lbf }

    NOTICE:
    While keeping the nut from rotating, tighten the bolt.

  1. Install the front lower No. 1 suspension arm sub-assembly LH to the front lower ball joint assembly with the bolt and 2 nuts.

    Torque:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }



2. INSTALL ENGINE MOUNTING INSULATOR LH (for LH Side)


    C242569E01
  1. Set the engine mounting insulator LH on the front frame assembly.
    Text in Illustration 
    *a
    Pin

  1. Slowly lower the engine assembly with transaxle using a jack and a wooden block.

    NOTICE:
    1. Match the position of the pin (stopper).
    2. Do not position the wooden block on the oil pan.
    3. Do not damage the components surrounding the engine assembly with transaxle.
    4. Ensure that the jack and wooden block are stable.



    C246189E01
  1. Using SST, install the nut to the engine mounting insulator LH.

    SST
    09961-00950  
    Text in Illustration 
    *a
    Fulcrum Length

    Torque:
    without SST:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }
    with SST:
    68 N*m{ 695 kgf*cm , 50 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 380 mm (1.25 ft.).
    2. This torque value is effective when SST is parallel to the torque wrench.



    C243740
  1. Install the engine mounting insulator LH with the 3 nuts.

    Torque:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }

  1. Install the 2 hole plugs.



3. INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for RH Side)
  1. Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly RH.



    C239314E01
  1. Install the front lower No. 1 suspension arm sub-assembly RH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

    Torque:
    Bolt 1, 2:
    200 N*m{ 2039 kgf*cm , 148 ft.*lbf }
    Bolt 3:
    135 N*m{ 1377 kgf*cm , 100 ft.*lbf }

    NOTICE:
    While keeping the nut from rotating, tighten the bolt.

  1. Install the front lower No. 1 suspension arm sub-assembly RH to the front lower ball joint assembly with the bolt and 2 nuts.

    Torque:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }



4. INSTALL ENGINE MOUNTING INSULATOR RH (for RH Side)


    C246172E01
  1. Set the engine mounting insulator RH on the front frame assembly.
    Text in Illustration 
    *a
    Cutout

  1. Slowly lower the engine assembly with transaxle using a jack and a wooden block.

    NOTICE:
    1. Match the position of the cutout (stopper).
    2. Do not position the wooden block on the oil pan.
    3. Do not damage the components surrounding the engine assembly with transaxle.
    4. Ensure that the jack and wooden block are stable.



    C239301E01
  1. Using SST, install the nut to the engine mounting insulator RH.

    SST
    09961-00950  
    Text in Illustration 
    *a
    Fulcrum Length

    Torque:
    without SST:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }
    with SST:
    68 N*m{ 695 kgf*cm , 50 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 380 mm (1.25 ft.).
    2. This torque value is effective when SST is parallel to the torque wrench.



    C247254
  1. Install the engine mounting insulator RH with the 3 nuts.

    Torque:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }

  1. Install the 2 hole plugs.



5. INSTALL FRONT ENGINE MOUNTING INSULATOR
  1. Install the front engine mounting insulator to the front frame assembly with the 3 nuts.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



6. CONNECT OXYGEN SENSOR
  1. Connect the oxygen sensor connector.



7. CONNECT NO. 4 ENGINE WIRE
  1. Connect the No. 4 engine wire to the front frame assembly with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



8. INSTALL FRONT FENDER APRON SEAL LH (for LH Side)


9. INSTALL FRONT FENDER APRON SEAL RH (for RH Side)


10. INSTALL ENGINE UNDER COVER LH


11. INSTALL ENGINE UNDER COVER RH


12. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH


13. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH


14. INSTALL ENGINE MOVING CONTROL ROD BRACKET


    C242572
  1. Temporarily install the engine moving control rod bracket with the 4 bolts.

  1. Fully tighten the engine moving control rod bracket with the 4 bolts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }



15. INSTALL NO. 2 ENGINE MOUNTING STAY RH
  1. Install the No. 2 engine mounting stay RH with the 2 bolts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }



16. INSTALL EARTH WIRE
  1. Install the earth wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



17. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
  1. Install the front outer cowl top panel sub-assembly with the 10 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.



18. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
  1. Install the front outer cowl top panel sub-assembly with the 10 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.



19. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for LHD)



20. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)



21. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }



22. INSTALL INVERTER WITH CONVERTER ASSEMBLY



23. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)