FRONT LOWER SUSPENSION ARM > INSTALLATION |
| 1. INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for LH Side) |
Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly LH.
![]() |
Install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.
Install the front lower No. 1 suspension arm sub-assembly LH to the front lower ball joint assembly with the bolt and 2 nuts.
| 2. INSTALL ENGINE MOUNTING INSULATOR LH (for LH Side) |
![]() |
Set the engine mounting insulator LH on the front frame assembly.
| *a | Pin |
Slowly lower the engine assembly with transaxle using a jack and a wooden block.
![]() |
Using SST, install the nut to the engine mounting insulator LH.
| *a | Fulcrum Length |
![]() |
Install the engine mounting insulator LH with the 3 nuts.
Install the 2 hole plugs.
| 3. INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for RH Side) |
Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly RH.
![]() |
Install the front lower No. 1 suspension arm sub-assembly RH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.
Install the front lower No. 1 suspension arm sub-assembly RH to the front lower ball joint assembly with the bolt and 2 nuts.
| 4. INSTALL ENGINE MOUNTING INSULATOR RH (for RH Side) |
![]() |
Set the engine mounting insulator RH on the front frame assembly.
| *a | Cutout |
Slowly lower the engine assembly with transaxle using a jack and a wooden block.
![]() |
Using SST, install the nut to the engine mounting insulator RH.
| *a | Fulcrum Length |
![]() |
Install the engine mounting insulator RH with the 3 nuts.
Install the 2 hole plugs.
| 5. INSTALL FRONT ENGINE MOUNTING INSULATOR |
Install the front engine mounting insulator to the front frame assembly with the 3 nuts.
| 6. CONNECT OXYGEN SENSOR |
Connect the oxygen sensor connector.
| 7. CONNECT NO. 4 ENGINE WIRE |
Connect the No. 4 engine wire to the front frame assembly with the bolt.
| 8. INSTALL FRONT FENDER APRON SEAL LH (for LH Side) |
| 9. INSTALL FRONT FENDER APRON SEAL RH (for RH Side) |
| 10. INSTALL ENGINE UNDER COVER LH |
| 11. INSTALL ENGINE UNDER COVER RH |
| 12. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH |
| 13. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH |
| 14. INSTALL ENGINE MOVING CONTROL ROD BRACKET |
![]() |
Temporarily install the engine moving control rod bracket with the 4 bolts.
Fully tighten the engine moving control rod bracket with the 4 bolts.
| 15. INSTALL NO. 2 ENGINE MOUNTING STAY RH |
Install the No. 2 engine mounting stay RH with the 2 bolts.
| 16. INSTALL EARTH WIRE |
Install the earth wire with the bolt.
| 17. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD) |
Install the front outer cowl top panel sub-assembly with the 10 bolts.
Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.
| 18. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
Install the front outer cowl top panel sub-assembly with the 10 bolts.
Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.
Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.
| 19. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for LHD) |
| 20. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD) |
| 21. INSTALL FRONT WHEELS |
| 22. INSTALL INVERTER WITH CONVERTER ASSEMBLY |
| 23. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |