Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    A259067
  1. Disengage the claw to remove the luggage trim service hole cover.



3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B288548
  1. Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.



5. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    B288549
  1. Disengage the 3 clips and remove the front door lower frame bracket garnish.



6. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B281681
  1. Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

  1. Disconnect each connector and remove the multiplex network master switch assembly with front door armrest base panel.



7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B281683
  1. Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

  1. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.



8. REMOVE FRONT ARMREST ASSEMBLY


    B277187
  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.



9. REMOVE COURTESY LIGHT ASSEMBLY


    E226714E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side
    *1
    Protective Tape

  1. Disconnect the connector and remove the courtesy light assembly.



10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B288550E01
  1. Put protective tape around the front door panel.
    Text in Illustration 
    *1
    Protective Tape



    B288551
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 10 clips.



    B288552E01
  1. Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
    Text in Illustration 
    *1
    Reference Boss
    *2
    Front Door Inner Glass Weatherstrip

  1. Disengage the reference boss from the front door panel.

  1. Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

  1. Disconnect the connector.



    B277192
  1. Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.



11. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    B277195E01
  1. Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Screwdriver



12. REMOVE FRONT DOOR SERVICE HOLE COVER


    B281686
  1. Disconnect each connector.

  1. Disengage the 4 clamps.

  1. Remove the front door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



13. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    B281733
  1. Remove the grommet.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Disconnect the multiplex network master switch assembly.



    B288542
  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.



    B288543E01
  1. Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.



14. REMOVE FRONT DOOR GLASS RUN


    B281735
  1. Remove the front door glass run.



15. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B288544
  1. Remove the 2 bolts.

  1. Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.



16. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (w/ Lock Cylinder)


    B280351
  1. Remove the hole plug.



    B280352
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



17. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY


    B280361E01
  1. Using a T30 "TORX" socket wrench, remove the 3 screws.
    Text in Illustration 
    *1
    Front Door Lock Open Rod

  1. Slide the front door lock with motor assembly downward, and remove the front door lock with motor assembly and cables as a unit.



  1. When reusing the front door lock with motor assembly:



      B280363
    1. Remove the door lock wiring harness seal from the front door lock with motor assembly.



18. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B280364
  1. Remove the front door lock remote control cable assembly.



19. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B280366
  1. Using a screwdriver, disengage the 3 claws.



    B280367
  1. Remove the front door inside locking cable assembly.