Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK

REAR DOOR LOCK > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    A259067
  1. Disengage the claw to remove the luggage trim service hole cover.



3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B280387
  1. Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.



5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B291314
  1. Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



6. REMOVE REAR ARMREST ASSEMBLY


    B280391
  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.



7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B280590E01
  1. Put protective tape around the rear door panel.
    Text in Illustration 
    *1
    Protective Tape



    B280393
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 8 clips.



    B280394E01
  1. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
    Text in Illustration 
    *1
    Reference Boss
    *2
    Rear Door Inner Glass Weatherstrip

  1. Disengage the reference boss from the rear door panel.

  1. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.



    B280396
  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

  1. Disconnect the connector.



    B280399E01
  1. Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Screwdriver



8. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    B280398E01
  1. Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Screwdriver



9. REMOVE REAR DOOR SERVICE HOLE COVER


    B281690
  1. Disconnect the connector and remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



10. DISCONNECT REAR DOOR WEATHERSTRIP


    B288951
  1. Disconnect the upper part of rear door weatherstrip as shown in the illustration.



11. REMOVE REAR DOOR GLASS RUN


    B280408
  1. Remove the rear door glass run.



12. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    B280409
  1. Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.

    NOTICE:
    When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.



13. REMOVE REAR DOOR QUARTER WINDOW GLASS


    B280410
  1. Remove the rear door quarter window glass as shown in the illustration.



14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B281692
  1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.



15. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY


    B280420E01
  1. Using a T30 "TORX" socket wrench, remove the 3 screws.
    Text in Illustration 
    *1
    Release Plate

  1. Move the rear door lock with motor assembly downward and pull the release plate out of the rear door outside handle frame.



  1. When reusing the rear door lock with motor assembly:



      B280422
    1. Remove the door lock wiring harness seal from the rear door lock with motor assembly.



16. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B280423
  1. Using a screwdriver, disengage the claw.



    B280425
  1. Remove the rear door lock remote control cable assembly.



17. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    B280427
  1. Using a screwdriver, disengage the 3 claws.



    B280429
  1. Remove the rear door inside locking cable assembly.