Home › Vehicle Interior › SEAT › REAR SEAT RECLINING CONTROL CABLE

REAR SEAT RECLINING CONTROL CABLE > INSTALLATION

for Preparation Click here



1. INSTALL REAR SEATBACK LOCK SUB-ASSEMBLY LH
  1. Install the rear seatback lock sub-assembly LH with the 2 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



2. INSTALL REAR SEATBACK LOCK SUB-ASSEMBLY RH
  1. Install the rear seatback lock sub-assembly RH with the 2 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    B294605E01
  1. Engage the hook in the order indicated in the illustration.



3. INSTALL ROOM PARTITION BOARD RH
  1. Engage the 4 clips to install the room partition board RH.

  1. Install the 4 clips.



4. INSTALL ROOM PARTITION BOARD LH
  1. Engage the 5 claws and clip to install the room partition board LH.

  1. Install the clip.



5. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
  1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.



    B381283
  1. Engage the guide and 3 clips to install the package tray trim panel assembly.



6. INSTALL REAR SEAT SHOULDER BELT COVER


    B271098
  1. Engage the 4 guides and 2 claws to install the rear seat shoulder belt cover.

    HINT:
    Use the same procedure for the other 2 rear seat shoulder belt covers.



7. INSTALL ROOF SIDE INNER GARNISH LH
  1. Engage the guide.

  1. Engage the 5 clips to install the roof side inner garnish LH.



8. INSTALL ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure as for the LH side.



9. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B278982E01
  1. Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
    Text in Illustration 
    *1
    Alignment Mark (Red)

    NOTICE:
    After installation, check that the corners fit correctly.



10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B278983E01
  1. Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
    Text in Illustration 
    *1
    Alignment Mark (Blue)

    NOTICE:
    After installation, check that the corners fit correctly.



11. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


    B279455E03
  1. Connect the floor anchor of the rear seat inner with center belt assembly LH with the bolt.
    Text in Illustration 
    *a
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Install the rear seat inner with center belt assembly LH with the arrow on the anchor part facing the front of the vehicle.
    2. Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.



12. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH
  1. Install the child restraint seat anchor bracket sub-assembly LH with the 2 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



13. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    B279441E05
  1. Connect the floor anchor of the rear seat outer belt assembly with the bolt.
    Text in Illustration 
    *a
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.



14. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    B279443E02
  1. Connect the floor anchor of the rear seat outer belt assembly with the bolt.
    Text in Illustration 
    *a
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.



15. INSTALL REAR SIDE SEATBACK ASSEMBLY LH
  1. Place the rear side seatback assembly LH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Engage the hook to install the rear side seatback assembly LH with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the rear seat outer belt to the rear seat shoulder belt guide LH.



16. INSTALL REAR SIDE SEATBACK ASSEMBLY RH
  1. Place the rear side seatback assembly RH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Engage the hook to install the rear side seatback assembly RH with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the rear seat outer belt to the rear seat shoulder belt guide RH.



17. INSTALL REAR SEATBACK ASSEMBLY LH
  1. Place the rear seatback assembly LH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly LH with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    B285008E01
  1. Engage the fastener as shown in the illustration.
    Text in Illustration 
    *1
    Fastener

  1. Raise the rear seatback assembly LH.

  1. Connect the rear seat outer belt to the rear seat center shoulder belt guide.



18. INSTALL NO. 2 ROOM PARTITION COVER


    B284996
  1. Engage the guide and claw to install the No. 2 room partition cover.



19. INSTALL REAR SEATBACK ASSEMBLY RH
  1. Place the rear seatback assembly RH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly RH with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    B284993E01
  1. Engage the fastener as shown in the illustration.
    Text in Illustration 
    *1
    Fastener

  1. Raise the rear seatback assembly RH.



20. INSTALL REAR SEAT CUSHION LOCK HOOK


    B280246
  1. Engage the claw to install a new rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure as for the LH side.



21. INSTALL REAR SEAT CUSHION ASSEMBLY
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B298857
  1. Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

  1. Confirm that the rear seat cushion assembly is firmly installed.

    NOTICE:
    When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.



22. INSTALL REAR SEAT HEADREST ASSEMBLY