Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

HYBRID CONTROL SYSTEM > ECU Power Source Circuit

for Preparation Click here


DESCRIPTION

If the power switch is on (IG), the power management control ECU applies current to the MREL terminal to turn the IGCT relay on. This supplies power to the +B1 and +B2 terminals.

WIRING DIAGRAM


A260348E05

Refer to the wiring diagram for DTC P0A08-264 .

INSPECTION PROCEDURE

1.CHECK POWER MANAGEMENT CONTROL ECU (+B1, +B2 VOLTAGE)
  1. Turn the power switch on (IG).



    A252924E49
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A39-3 (+B1) - Body ground
    Power switch on (IG)
    11 to 14 V
    A38-1 (+B2) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)

  1. Turn the power switch off.



NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect connector I3 and I4 from the power management control ECU.



    A253458E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I3-5 (E01) - Body ground
    Always
    Below 1 Ω
    I3-6 (E1) - Body ground
    Always
    Below 1 Ω
    I4-4 (E12) - Body ground
    Always
    Below 1 Ω
    I4-5 (E02) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Connect the power management control ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO PROBLEM SYMPTOMS TABLE (Click here)  

3.CHECK POWER MANAGEMENT CONTROL ECU (MREL VOLTAGE)
  1. Turn the power switch on (IG).



    A252924E50
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A38-4 (MREL) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK


4.CHECK FUSE (PM IGCT)


    A260347E01
  1. Remove the PM IGCT fuse from the No. 2 engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PM IGCT fuse terminals
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    PM IGCT Fuse

  1. Install the PM IGCT fuse.



NG
Go to step 13
OK


5.CHECK FUSE (IGCT-MAIN)


    A259797E01
  1. Remove the IGCT-MAIN fuse from the No. 2 engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IGCT-MAIN fuse terminals
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    IGCT-MAIN Fuse

  1. Install the IGCT-MAIN fuse.



NG
Go to step 15
OK


6.INSPECT RELAY (IGCT)
  1. Remove the IGCT relay from the No. 2 engine room relay block.



    A253297E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Auxiliary battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    Auxiliary battery voltage is applied between terminals 1 and 2
    Below 1 Ω

    Text in Illustration 
    *1
    IGCT Relay

  1. Install the IGCT relay.



NG
REPLACE RELAY (IGCT)
OK


7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK)


    A260347E01
  1. Remove the PM IGCT fuse from the No. 2 engine room relay block.
    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    PM IGCT Fuse

  1. Disconnect connector A38 and A39 from the power management control ECU.



  1. Measure the resistance according to the value(s) in the table below.


    A266964E06


    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    PM IGCT Fuse
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-3 (+B1) - 2 (PM IGCT fuse)
    Always
    Below 1 Ω
    A38-1 (+B2) - 2 (PM IGCT fuse)
    Always
    Below 1 Ω

  1. Install the PM IGCT fuse.

  1. Connect the power management control ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK)


    A260385E01
  1. Remove the IGCT-MAIN fuse and PM IGCT fuse from the No. 2 engine room relay block.
    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    PM IGCT Fuse
    *3
    IGCT-MAIN Fuse

  1. Remove the IGCT relay from the No. 2 engine room relay block.



    A260386E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (IGCT relay) - 2 (IGCT-MAIN fuse)
    Always
    Below 1 Ω
    5 (IGCT relay) - 1 (PM IGCT fuse)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    PM IGCT Fuse
    *3
    IGCT Relay
    *4
    IGCT-MAIN Fuse

  1. Install the IGCT-MAIN fuse and PM IGCT fuse.

  1. Install the IGCT relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK)
  1. Remove the IGCT relay from the No. 2 engine room relay block.

  1. Disconnect connector A38 from the power management control ECU.



  1. Measure the resistance according to the value(s) in the table below.


    A330590E01


    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    IGCT Relay
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A38-4 (MREL) - 1 (IGCT relay)
    Always
    Below 1 Ω
    A38-4 (MREL) or 1 (IGCT relay) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Install the IGCT relay.

  1. Connect the power management control ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK - BODY GROUND)
  1. Remove the IGCT relay from the No. 2 engine room relay block.



    A259798E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (IGCT relay) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    IGCT Relay

  1. Install the IGCT relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - NO. 2 ENGINE ROOM RELAY BLOCK)
  1. Remove the IGCT-MAIN fuse from the No. 2 engine room relay block.

  1. Disconnect AMD terminal from the engine room relay block and junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    A260388E01


    Text in Illustration 
    *1
    Engine Room Relay Block and Junction Block Assembly
    *2
    No. 2 Engine Room Relay Block
    *3
    IGCT-MAIN Fuse
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1K-1 (AMD) - 1 (IGCT-MAIN fuse)
    Always
    Below 1 Ω

  1. Install the IGCT-MAIN fuse.

  1. Connect AMD terminal.



NG
Go to step 12
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

12.CHECK FUSIBLE LINK BLOCK ASSEMBLY (R/B NO. 2)
  1. Check the fusible link block assembly (R/B NO. 2) in the engine room relay block and junction block assembly for improper installation.

    OK:
    The fusible link is installed securely.

  1. Remove the fusible link block assembly from the engine room relay block and junction block assembly.



    A258447E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Fusible link block assembly 1 -2 terminals (R/B NO. 2)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Fusible Link Block Assembly

  1. Install the fusible link block assembly.



NG
REPLACE FUSIBLE LINK BLOCK ASSEMBLY (R/B NO. 2)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

13.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK)
  1. Disconnect connector E73 from the shift lever position sensor.



    A260347E01
  1. Remove the PM IGCT fuse from the No. 2 engine room relay block.
    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    PM IGCT Fuse

  1. Disconnect connectors A38 and A39 from the power management control ECU.



  1. Measure the resistance according to the value(s) in the table below.


    A266964E06


    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    PM IGCT Fuse
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-3 (+B1) or 2 (PM IGCT fuse) - Body ground and other terminals
    Always
    10 kΩ or higher
    A38-1 (+B2) or 2 (PM IGCT fuse) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Install the PM IGCT fuse.

  1. Connect the shift lever position sensor connector.

  1. Connect the power management control ECU connectors.



NG
Go to step 14
OK

REPLACE FUSE (PM IGCT) 

14.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (PM IGCT) 

15.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK)


    A260385E01
  1. Remove the IGCT-MAIN fuse and PM IGCT fuse from the No. 2 engine room relay block.
    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    PM IGCT Fuse
    *3
    IGCT-MAIN Fuse

  1. Remove the IGCT relay from the No. 2 engine room relay block.



    A260386E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (IGCT relay) or 2 (IGCT-MAIN fuse) - Body ground and other terminals
    Always
    10 kΩ or higher
    5 (IGCT relay) or 1 (PM IGCT fuse) - Body ground and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    PM IGCT Fuse
    *3
    IGCT Relay
    *4
    IGCT-MAIN Fuse

  1. Install the IGCT-MAIN fuse and PM IGCT fuse.

  1. Install the IGCT relay.



NG
Go to step 16
OK

REPLACE FUSE (IGCT-MAIN) 

16.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (IGCT-MAIN)