Home › Audio / Visual / Telematics › AUDIO / VIDEO › NOISE FILTER

NOISE FILTER > INSTALLATION

for Preparation Click here



1. INSTALL RADIO SETTING CONDENSER (for Window Defogger)


    E183101
  1. Engage the claw to install a new terminal cover to the wire harness.

    NOTICE:
    1. Make sure to hold the wire harness so that the crimping side of the terminal is facing up when installing the wire harness to the terminal cover.
    2. Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.
    3. Do not use excessive force when inserting the wire harness into the terminal cover.
    4. If the terminal cover has been deformed at installation, replace the terminal and terminal cover with new ones.



    E221975
  1. Engage the 3 claws to install the new terminal cover with wire harness to a new condenser.

    NOTICE:
    1. Do not use excessive force when inserting the terminal cover into the condenser.
    2. If the terminal cover has been deformed at installation, replace the terminal, terminal cover and condenser with new ones.

  1. Engage the 2 clamps to temporarily install a new radio setting condenser with wire harness.

  1. Install the new radio setting condenser with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



2. INSTALL ROOF SIDE INNER GARNISH LH (for Window Defogger)
  1. Engage the guide.

  1. Engage the 5 clips to install the roof side inner garnish LH.



3. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Window Defogger)


    B278982E01
  1. Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
    Text in Illustration 
    *1
    Alignment Mark (Red)

    NOTICE:
    After installation, check that the corners fit correctly.



4. INSTALL RADIO SETTING CONDENSER (for High Mounted Stop Light)


    E226085
  1. Engage the claw to install a new terminal cover to the wire harness.

    NOTICE:
    1. Make sure to hold the wire harness so that the crimping side of the terminal is facing up when installing the wire harness to the terminal cover.
    2. Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.
    3. Do not use excessive force when inserting the wire harness into the terminal cover.
    4. If the terminal cover has been deformed at installation, replace the terminal and terminal cover with new ones.



    E223710
  1. Engage the 6 claws to install the 2 new terminal covers with wire harness to a new condenser.

    NOTICE:
    1. Do not use excessive force when inserting the terminal cover into the condenser.
    2. If the terminal cover has been deformed at installation, replace the terminal, terminal cover and condenser with new ones.



    E226095
  1. Engage the claw to insert the cover as shown in the illustration.

  1. Engage the clamp to temporarily install a new radio setting condenser with wire harness.

  1. Install the new radio setting condenser with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



5. INSTALL REAR SIDE SEATBACK ASSEMBLY LH
  1. Place the rear side seatback assembly LH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Engage the hook to install the rear side seatback assembly LH with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the rear seat outer belt to the rear seat shoulder belt guide LH.



6. INSTALL REAR SEAT CUSHION LOCK HOOK


    B280246
  1. Engage the claw to install a new rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure as for the LH side.



7. INSTALL REAR SEAT CUSHION ASSEMBLY
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B298857
  1. Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

  1. Confirm that the rear seat cushion assembly is firmly installed.

    NOTICE:
    When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.